We use cookies on this site

< Packages Visualise

Firmware GPA (M150).July 2015

Image Resource M150 Firmware

Details

285
GPA (M150)
July 2015 (1.05)
GPA (M150).July 2015
Public
M1 GPA (23061)

Options

Included
Available (extra cost)

Description

-


Packages for this Version: July 2015
Name Version
V [] Generic 4 cylinder, MAP based Efficiency Migration Base July 2015 (1.05.0004)
Release Notes

Current Version

  • Implement Resource hiding: objects are not shown in Tune when no resources are assigned.
  • Implement Calibration support: Configured settings for numerous sensors selectable.
  • Tagging of objects for facilitated selection in Tune, especially for logging setup.
  • Resources allow for directly selecting CAN inputs.
  • Test functionalities added: outputs can be activated using test settings.
  • Added Alternator control.
  • Added Brake Vacuum sensor and pump.
  • Brake pressures have separate threshold to set Brake State.
  • Added Differential temperature sensor and pump.
  • 2 Switches and 4 Rotary Switches have been added for driver interaction.
  • Added Boost Limit Disable switch.
  • Boost Control will be disabled when no Boost Pressure Sensor and Inlet Maifold Pressure Sensor is available.
  • ECU Power Relay powered on during cranking.
  • ECU Receive (CAN): Also compound messages can be received now.
  • Increase size of Engine Efficiency map.
  • Introduce Engine Charge Temperature as a corrected Inlet Air Temperature.
  • Camshafts: Additional output added for VANOS support.
  • Exhaust Temperature Warning now uses highest available temperature as trigger.
  • Added Fuel Temperature Estimate as a fall back value.
  • Added 2 Fuel Flow sensors.
  • Adjusted Fuel Pressure to better suit regulator types.
  • Gear Position Sensor changed to dual sensor.
  • Added Gear dependent Throttle Limit and Ignition Timing Trim.
  • Inlet Manifold Pressure Estimate: modify fallbacks when Mode is Boost Relative.
  • Rename Inlet Manifold Temperature to Inlet Air Temperature.
  • Inlet Manifold Temperature is now describing the inlet manifold body temperature, which can be used to correct the Inlet Air Temperature Sensor (for example in case of heat soak problems).
  • Added Inlet Manifold Flap and Inlet Manifold Runner support (actuator plus position feedback).
  • Switched inlet camshaft has an addition threshold to switch off the actuator.
  • Ignition Coil Charge Time Trim added for scaling of the time in dependency of engine load.
  • Idle Throttle Pedal Blend for acceleration feel adjustment.
  • Idle Stepper motor support added.
  • Intercooler: additional Ambient Temperature threshold, more flexible temperature delta calculation.
  • Knock: It can be selected which frequencies contribute to the determined knock level.
  • LTC Enable CAN message (0x480) can be deactivated.
  • Lap Time: Can now also be sourced from a GPS input.
  • Tachometer output pin measurement.
  • Throttle Position Estimate added as a fall back when no valid source for Throttle Position is available.
  • Throttle Servo can be reinitialised after an error.
  • Throttle Servo and Pedal support digital sensors and nonlinear tracking sensors.
  • Turbocharger Bypass functionality added.
  • Added Vehicle Speed Limit functionality.
  • Delay switching Vehicle Speed sources to consider spinning wheels.

Base version: December 2014, 01.02.0001

Notes

The Options line indicates options that are associated with this. The association indicates how the option affects ordering.

  • Available: the option may be added to an order.
  • Included: the option will be added to the order, and not charged for.
  • Prerequisite: the option will be added to the order, and charged for.

The different Packages contain different tuning data.