We use cookies on this site

< Sea-Doo RXT-X 2010 (M150).June 2020

Package Sea-Doo RXT-X 2010 (M150).June 2020 "1.4 Start File v3"

Sea-Doo RXT-X 2010 (M150).June 2020
1.4 Start File v3
Sea-Doo RXT-X 2010 (M150).June 2020
01.02.0051
12/08/2021




Release Notes
The Migration Notes lists the changes required, when upgrading, to maintain the same functionality from the previous version.

Current Version (01.02.0051)

  • System updated to version 1.4.0.91
  • Support for Batch Fire fuel injection added.
  • GPS via RS232 functionality added for M130 (Rev Q+) and M122 ECU's.
  • Motec GPS Module update to v1.7.21.
    • Serial Port Resource and Baud rate can be set externally.
    • Update system version to 1.4.0.0091.
    • Add support for M130 Rev Q. hardware with RS232 Rx on Udig 6 and 7.
    • Moves the serial port setup inside the GPS group.
    • Ensure a Diagnostic of Invalid Interface is reported correctly for all hardware types.
    • Allow any CAN Decode message to set the Diagnostic to OK. Allows GPS Speed message to be received by itself for example.
    • Help Updates.
  • Motec Fuel Module update to v1.18.1
    • System update to 1.4.0.91.
    • Allowance for Revolution Lock and Cylinder Lock Engine Speed Reference State in Single, Double, Triple and Quadruple Injector Fuel Volume classes. Required for Batch Fire Injection.
    Motec Input Module update to v1.10.36
    • Remove 'Diagnostic Delay' validation maximum.
    • Resource re-ordered in latchable switch class.
    Motec Comms Module updated to 1.10.3
    • System updated to v1.04.0091.
    • Serial Port class removed.
    Migration Notes;
    • Set GPS Serial Port Resource and GPS Serial Port Baud Rate if GPS Interface is RS232 Port.

01.02.0050

  • Cruise updated.
  • No Wake updated.
  • Vehicle Speed Limit added.
    • Migration Notes;
    • Set Cruise Enable Throttle Lever Hysteresis to Cruise Throttle Lever Hysteresis from the old package.

01.02.0046

  • Race Time axis added to Fuel Mixture Aim Trim.

01.02.0045

  • Engine Start updated.

01.02.0042

  • Driver Engine Speed Limit Switch converted to 3 position switches.
  • Driver Ignition Timing Main Switch axis added to Ignition Timing Trim Main table.

01.02.0040

  • Ignition Timing Trim Main added.

01.02.0039

  • Driver Fuel Mixture Aim and Driver Ignition Timing Main Switches converted to 3 position switches.

01.02.0038

  • Engine Run updated to be disabled by Engine Start Switch when Type is Push Button.

01.02.0036

  • Vehicle Tip Over updated to include a delay.

01.02.0035

  • MoTeC OE SeaDoo RXTX module updated to v 1.0.12
    • RXTX 2018 and 2019 models added.
  • Throttle Aim set to Idle while Seadoo Braking.
  • Gear Shift Mode bug fixed.
  • Vehicle Speed Limit from Seadoo Cruise added.
  • Vehicle Tip Over Warning removed.
  • Engine Start updated.

01.02.0029

  • Engine Start Delay added.

01.02.0028

  • Throttle Limit added to all Warnings.

01.02.0025

  • Throttle Servo Fault Engine Speed Limit applied when Throttle Servo Bank N Diagnostic is Power Save.
  • LTC enable strategy improved to better suit marine applications.
  • Gear Source added.
  • Engine Run Time Reset Value added.

01.02.0018

  • Engine Oil Temperature Estimate available when sensor is not in use.
  • Engine Oil Pressure Low Switch updated.

01.02.0017

  • Fuel Tank Level Warning and Warning Light added.

01.02.0016

  • Engine Oil Pressure Low Switch Engine Speed Minimum and Hysteresis added.

01.02.0015

  • Engine Start updated.
  • Engine Stop updated.
  • Engine Oil Pressure Low Switch updated.

01.02.0010

  • Forward 2 removed from Gear.

01.02.0006

  • Vehicle speed updated.

01.02.0004

  • M1 General 0x640 CAN Template reverted to version 5.
  • M1 General 0x650 CAN Template reverted to version 5.
  • M1 General 0x6A0 CAN Template reverted to version 1.
  • Engine Stop Switch bug fixed.
  • Engine Starter Motor renamed to Engine Start Motor.
    • Migration Notes;
    • Update any M1_General_0x640 CAN templates to M1_General_0x640_Version 5.
    • Update any M1_General_0x650 CAN templates to M1_General_0x650_Version 5.
    • Update any M1_General_0x6A0 CAN template to M1_General_0x6A0_Version 1.

01.02.0003

  • Coolant Pump added.
  • Engine Start updated.
  • Engine Starter Motor updated.
  • Engine Stop Switch added.

01.02.0002

  • System updated to version 1.4.0.79.
  • ADR added.
  • Airbox Mass Flow added.
  • Airbox Temperature Sensor Resource object name changed from Airbox Temperature Sensor Voltage Resource.
  • Airbox Temperature Sensor updated
  • Airbox Pressure added.
  • Alternative Fuel added.
  • Alternator added.
  • Ambient Pressure updated
  • Ambient Temperature updated
  • Anti Lag updated
  • Anti Cavitation Mode enumeration changed. 'Disabled' value changed to 'Not in Use' to allow for hiding of unused objects.
  • Anti Cavitation Throttle Limit object name changed from Anti Cavitation Throttle.
  • Anti Cavitation Ignition Timing Trim object name changed from Anti Cavitation Ignition Timing Compensation.
  • Auxiliary Output 1-4 Resource object name changed from Auxiliary Output 1-5 Pulse Width Modulation Resource.
  • Auxiliary Output 1-4 Test added.
  • Auxiliary Output 1-4 Frequency added.
  • Auxiliary Output 1-4 Duty Cycle table validation limit minimum increased to -100%
  • Auxiliary Output 1-4 Activate Vehicle Speed added.
  • Auxiliary Output 1-4 Output object name changed from Auxiliary Output 1-5 Pulse Width Modulation.
  • Auxiliary Output 1 Ignition Timing Trim object name changed from Auxiliary Output 1 Ignition Timing Compensation.
  • Auxiliary Output 1 Fuel Volume Trim object name changed from Auxiliary Output 1 Fuel Volume Compensation.
  • Auxiliary Output 1 Fuel Mixture Aim added. Replaces Auxiliary Output 1 Fuel Mixture Compensation
  • Auxiliary Output 5 added.
  • Brake State added.
  • Boost updated
  • Cruise object name changed from Cruise Assist.
  • Cruise Mode enumeration changed. Paramaterd 'Disabled' value changed to 'Not in Use' to allow for hiding of unused objects.
  • Cruise Throttle object name changed from Cruise Assist Throttle.
  • Cruise Throttle Lever Hysteresis object name changed from Cruise Assist Throttle.
  • Cruise enable conditions updated to include Brake State
  • CAN Bus 1 object name changed from Communications CAN Bus.
  • Coolant Temperature Sensor updated
  • Coolant Temperature Warning updated
  • Coolant Temperature Estimate added.
  • Coolant Temperature Engine Speed Limit added.
  • Coolant Temperature Ignition Timing Compensation table axis modified. Coolant Temperature axis sites reduced to 11. Engine Load Normalised axis added.
  • Coolant Temperature Fuel Volume Compensation table axis modified. Coolant Temperature axis sites reduced to 11.
  • Coolant Temperature Fuel Mixture Aim added. Replaces Coolant Temperature Fuel Mixture Compensation
  • Coolant Temperature Boost Limit added. Replaces Coolant Temperature Boost Aim Compensation
  • Coolant Pressure added.
  • Driver Switches added.
  • Driver Anti Lag Switch object name changed from Anti Lag Switch.
  • Driver Cruise Set Switch object name changed from Cruise Assist Set Button.
  • Driver Cruise Up Switch object name changed from Cruise Assist Up Button.
  • Driver Cruise Down Switch object name changed from Cruise Assist Down Button.
  • E8XX added.
  • ECU CPU Usage added.
  • ECU Acceleration updated
  • ECU Acceleration X Sensor object name changed from ECU Acceleration X.
  • ECU Acceleration Y Sensor object name changed from ECU Acceleration Y.
  • ECU Acceleration Z Sensor object name changed from ECU Acceleration Z.
  • ECU Battery updated
  • ECU Power Relay updated
  • ECU Sensor & Internal voltages updated
  • ECU Receive updated
  • ECU Receive object name changed from Communications Receive.
  • ECU Transmit updated
  • ECU Transmit CAN Bus object name changed from Communication CAN Bus.
  • Engine Trip Time added.
  • Engine Efficiency Boost Pressure Compensation added.
  • Engine Efficiency Airbox Pressure Compensation added.
  • Engine Charge Temperature added.
  • Engine Charge Cooling updated
  • Engine Charge Cooling Gain Primary object name changed from Engine Charge Cooling Gain.
  • Engine Load Normalised added.
  • Engine Speed Limit Maximum table axis modified. X axis changed to Driver engine Speed Limit Maximum Switch
  • Engine Speed Limit Warning updated
  • Engine Synchronisation Resource added.
  • Engine Synchronisation Ignore and State added.
  • Engine Run added.
  • Engine Start Stop Switch object name changed from Engine Start Stop Button.
  • Engine Start Stop Switch updated
  • Engine Starter Motor object name changed from Starter Motor.
  • Engine Starter Motor Relay Resource object name changed from Starter Motor Relay Output Resource.
  • Engine Starter Motor Relay updated
  • Engine Crank Idle Mass Flow added.
  • Engine Crank Flooded Throttle Position added.
  • Engine Crank Fuel Volume Compensation object name changed from Fuel Volume Compensation Cranking.
  • Engine Post Start Idle Aim Compensation added.
  • Engine Post Start Idle Mass Flow Feed Forward added.
  • Engine Post Start Fuel Volume Compensation object name changed from Fuel Volume Compensation Post Start.
  • Engine Oil Temperature Sensor Resource object name changed from Engine Oil Temperature Sensor Voltage Resource.
  • Engine Oil Temperature Estimate added.
  • Engine Oil Temperature Engine Speed Limit added.
  • Engine Oil Temperature Sensor updated
  • Engine Oil Temperature Warning updated
  • Engine Oil Pressure Sensor updated
  • Engine Oil Pressure Low Switch updated
  • Engine Oil Pressure Warning updated
  • Engine Oil Level added.
  • Engine Temperature added.
  • Engine Overrun updated
  • Engine Crankcase added.
  • Engine Boost Limit added.
  • Engine Mode Switch removed. Replaced by Driver Fuel Mixture Aim Main Switch, Driver Ignition Timing Main Switch, Driver Engine Speed Limit Maximum Switch and Driver Throttle Lever Translation Switch.
  • Exhaust Lambda Bank 1 & 2 added.
  • Exhaust Lambda Warning added.
  • Exhaust Lambda External removed. Use Exhaust Lambda Collector instead.
  • Exhaust Lambda Collector CAN Bus added. Replaces Exhaust Lambda Collector Mode
  • Exhaust Lambda Cylinder 1-3 CAN Bus added. Replaces Exhaust Lambda Cylinder 1-3 Mode
  • Exhaust Pressure added.
  • Exhaust Temperature Maximum added.
  • Exhaust Temperature Boost Limit added. Replaces Exhaust Temperature Boost Limit Compensation
  • Exhaust Temperature Fuel Mixture Aim added. Replaces Exhaust Temperature Fuel Mixture Compensation
  • Exhaust Temperature Ignition Timing Compensation removed. Replaced by Engine Load Average Ignition Timing Trim.
  • Exhaust Temperature Bank 1 & 2 added.
  • Exhaust Temperature Collector Sensor Resource object name changed from Exhaust Temperature Collector Sensor Voltage Resource.
  • Exhaust Temperature Collector Sensor updated
  • Exhaust Temperature Cylinder 1-3 Sensor Resource object name changed from Exhaust Temperature Cylinder 1-3 Sensor Voltage Resource.
  • Exhaust Temperature Cylinder 1-3 Sensor updated
  • Exhaust Camshaft added.
  • Exhaust Muffler Temperature object name changed from Muffler Temperature.
  • Exhaust Muffler Temperature Sensor Resource object name changed from Muffler Temperature Sensor Voltage Resource.
  • Exhaust Muffler Temperature Sensor updated
  • Exhaust Muffler Temperature Warning updated
  • Fuel Used Primary Correction added.
  • Fuel Properties Calibration added.
  • Fuel Mixture Aim Main object name changed from Fuel Mixture Aim A.
  • Fuel Mixture Aim Compensation removed. No longer required.
  • Fuel Mixture Aim State added.
  • Fuel Volume Bank 1 & 2 added.
  • Fuel Volume Transient removed. Replaced by Fuel Film.
  • Fuel Mixture Aim B removed. Replaced by Fuel Mixture Aim Main and Driver fuel Mixture Aim Main Switch.
  • Fuel Timing Primary object name changed from Fuel Timing.
  • Fuel Timing Primary Main table axis modified. Engine Speed axis sites reduced to 11. Y axis changed to Inlet Manifold Pressure.
  • Fuel Timing Primary Limit table axis modified. Engine Speed axis sites reduced to 11.
  • Fuel Flow Supply & Return added.
  • Fuel Film added.
  • Fuel Temperature Estimate added.
  • Fuel Temperature Sensor updated
  • Fuel Pressure Estimate added.
  • Fuel Pressure Default added.
  • Fuel Pressure Control added.
  • Fuel Pressure Regulator Type added. Replaces Fuel Pressure Sensor Type & Regulator Reference
  • Fuel Pressure Regulator Ratio added. Replaces Fuel Pressure Sensor Type & Regulator Reference
  • Fuel Pressure Sensor updated
  • Fuel Pressure Warning updated
  • Fuel Water Content added.
  • Fuel Injector Primary updated
  • Fuel Pump updated
  • Fuel Pump 2 & 3 added.
  • Fuel Closed Loop Mode enumeration changed. 'Disabled' value changed to 'Not in Use' to allow for hiding of unused objects.
  • Fuel Closed Loop Activate Throttle Pedal added.
  • Fuel Cut. added. Replaces Fuel Diagnostic
  • Fuel Composition added.
  • Fuel Composition Boost Limit added.
  • Fuel Tank added. Replaces Fuel Level
  • Fuel Cylinder 1-3 Primary Output Resource object name changed from Fuel Cylinder 1-3 Output Resource.
  • Fuel Cylinder 1-3 updated
  • Gear added.
  • GPS updated
  • Idle added. Replaces Idle Throttle
  • Ignition Test added.
  • Ignition Cut added.
  • Ignition Coil Calibration added.
  • Ignition Coil Charge object name changed from Ignition.
  • Ignition Driver Firing Edge added.
  • Ignition Cylinder 1-3 updated
  • Ignition Cylinder 1-3 Resource object name changed from Ignition Cylinder 1-3 Output Resource.
  • Ignition Output Cut Pattern added.
  • Ignition Diagnostic removed. Replaced by Engine Run.
  • Ignition Switch removed. replaced by Engine Run Switch.
  • Ignition Timing Stop Edge removed. No longer required.
  • Inlet Air Temperature object name changed from Inlet Manifold Temperature. Replaces Inlet Manifold Temperature
  • Inlet Air Temperature Boost Limit added. Replace Inlet Manifold Temperature Boost Limit Compensation
  • Inlet Air Temperature Fuel Mixture Aim added. Replaces Inlet Manifold Temperature Fuel Mixture Aim Compensation
  • Inlet Manifold Pressure Mode added.
  • Inlet Manifold Pressure Estimate added.
  • Inlet Manifold Pressure Sensor updated
  • Inlet Manifold Pressure Warning added.
  • Inlet Manifold Pressure Correction added.
  • Inlet Manifold Temperature updated
  • Inlet Manifold Flap added.
  • Inlet Manifold Runner added.
  • Inlet Camshaft added.
  • Intercooler added.
  • Cruise Mode enumeration changed.
  • Knock Threshold table axis modified. Engine Speed and Engine Load Normalised axes sites reduced to 11. Fuel Composition axis added
  • Knock Recovery Rate table axis modified. Engine Speed axis sites reduced to 11. Engine Load Normalised axis added
  • Knock Activate added.
  • Knock Trim Gain table axis modified. Fuel Composition axis added.
  • Knock Window DSP object name changed from Knock Window Output.
  • Knock Warning updated
  • Knock Cylinder 1-3 added.
  • Knock Cylinder 1-3 Gain object name changed from Engine Cylinder 1-3.
  • Jet Nozzle Pressure Sensor Resource object name changed from Jet Nozzle Pressure Sensor Resource.
  • Jet Nozzle Pressure Sensor updated
  • Jet Nozzle Angle Horizontal Sensor Resource object name changed from Jet Nozzle Angle Horizontal Sensor Resource.
  • Jet Nozzle Angle Horizontal Sensor updated
  • Jet Intake Pressure Sensor Resource object name changed from Jet Intake Pressure Sensor Resource.
  • Jet Intake Pressure Sensor updated
  • Jet Intake Temperature object name changed from Water Temperature.
  • Jet Trim Sensor Resource object name changed from Jet Trim Sensor Resource.
  • Jet Trim Sensor updated
  • Lap added.
  • Lanyard Switch updated
  • Lanyard added.
  • Launch Engine Speed table axis modified. Driver Launch Aim switch axis added
  • Launch Fuel Volume Trim object name changed from Launch Fuel Volume Compensation.
  • Launch Switch removed. Replaced by Driver Launch Switch
  • Logging throttle Lever added.
  • Logging Engine Speed added.
  • Logging Unload added.
  • LTC added.
  • LTC Power Save Delay object name changed from Exhaust Lambda Power Save Delay.
  • Nitrous added.
  • No Wake object name changed from No Wake Mode.
  • No Wake Mode added.
  • No Wake Enable added.
  • No Wake Throttle Aim object name changed from No Wake Mode Throttle.
  • PDM added.
  • Race Time Mode added.
  • Race Time Mode updated
  • Race Time Activate Vehicle Speed added.
  • Race Time Activate Delay added.
  • Race Time Reset added.
  • Race Time Boost Limit added. Replaces Race Time Boost Limit Compensation
  • Race Time Fuel Mixture Aim added. Replace Race Time Fuel Mixture Aim Compensation
  • Race Time Ignition Timing Trim object name changed from Race Time Ignition Timing Compensation.
  • Race Time Throttle Limit added. Replaces Race Time Throttle Lever Compensation
  • SeaDoo CAN Bus added.
  • SeaDoo Model object name changed from Communications SeaDoo Model.
  • SeaDoo ADL Diagnostic object name changed from Communications ADL Diagnostic.
  • SeaDoo Brake object name changed from Brake.
  • SeaDoo GPS object name changed from Communications GPS.
  • SLM added.
  • Steering Angle added.
  • Steering Force added.
  • Steering Pressure added.
  • Steering Lock Switch Resource object name changed from Steering Lock Switch State Resource.
  • Steering Lock Switch updated
  • Steering Lock Throttle Aim object name changed from Steering Throttle.
  • Tachometer added.
  • Throttle Area table axis modified. Throttle Servo Position axis sites increased to 41
  • Throttle Lever Sensor Main Resource object name changed from Throttle Lever Sensor Main Voltage Resource.
  • Throttle Lever Sensor Tracking Resource object name changed from Throttle Lever Sensor Tracking Voltage Resource.
  • Throttle Lever Translation table axis modified. Engine Speed axis sites reduced to 21. Driver Throttle Lever Translation Switch axis added.
  • Throttle Lever Sensor updated
  • Throttle Lever Compensation removed. Replaced by Throttle Limit.
  • Throttle Limit added.
  • Throttle Aim Diagnostic added.
  • Throttle Aim Minimum added.
  • Throttle Cranking removed. Replaced by Throttle Aim Minimum and Idle control system
  • Throttle Dashpot removed. Replaced by Idle control system
  • Throttle Position Fuel Mixture Aim added.
  • Throttle Position Estimate added.
  • Throttle Position Sensor added.
  • Throttle Servo updated
  • Throttle Test updated
  • Turbocharger added.
  • VCS added.
  • Vehicle Speed updated
  • Vehicle Acceleration Lateral Sensor Resource object name changed from Vehicle Acceleration Lateral Sensor Voltage Resource.
  • Vehicle Acceleration Lateral Sensor updated
  • Vehicle Acceleration Longitudinal Sensor Resource object name changed from Vehicle Acceleration Longitudinal Sensor Voltage Resource.
  • Vehicle Acceleration Longitudinal Sensor updated
  • Vehicle Acceleration Vertical Sensor Resource object name changed from Vehicle Acceleration Vertical Sensor Voltage Resource.
  • Vehicle Acceleration Vertical Sensor updated
  • Vehicle Tip Over Switch updated
  • Vehicle Tip Over Switch Resource object name changed from Vehicle Tip Over Switch State Resource.
  • Vehicle Tip Over Warning updated
  • Warning Source added.
  • Warning Mode added.
  • Wastegate added.
    • Migration Notes;
    • Refer to migration document for this version.

Previous Version (01.01.0022)

Package Notes

From 1.4 Start File v2

Related Software
Versions
Version
01.02.0051

JSON Visibility: Hidden

Slug Override: N/A