We use cookies on this site

< Sea-Doo RXT-X 2010.June 2020

Package Sea-Doo RXT-X 2010.June 2020 "Sea-Doo RXP-X 2021 Rotax 1630 ACE Start File v8"

Sea-Doo RXT-X 2010.June 2020
Sea-Doo RXP-X 2021 Rotax 1630 ACE Start File v8
Sea-Doo RXT-X 2010.June 2020
01.02.0144
9/02/2023




Release Notes
The Migration Notes lists the changes required, when upgrading, to maintain the same functionality from the previous version.

Current Version (1.02.0144)

  • Water Temperature added and added to ECU Transmit message 0x6A0
    • Migration Notes
    • Update M1 Watercraft 0x6A0 CAN template to V3

1.02.0137

  • ECU Transmit Custom CAN added
  • MoTeC Comms Module updated to 1.10.25
    • 800kbps baud rate added to CAN Bus class.

1.02.0131

  • MoTeC Control Module Updated to 1.12.123.
    • Actuator Outpt resource no longer required for Boost control to be active.
    • Boost Control system will now operate without assigning a Boost Solenoid Normal Output Resource in Boost with Servo class.
  • Neutral Gear only option added to Engine Overrun Mode.

01.02.0125

  • Cruise updates.
  • MoTeC OE SeaDoo RXTX module updated to v 1.0.26
  • Slow Speed Enable Delay added. This overrides the hardcoded 1s delay when enabling slow Speed.
    • Migration Notes;
    • Set Slow Speed Enable Delay to 1.0s.

01.02.0121

  • MoTeC OE SeaDoo RXTX module updated to v 1.0.24
    • Cruise updates.
    • Slow Speed updates.

01.02.0120

  • Renamed No Wake to Slow Speed with various updates to the feature.

01.02.0117

01.02.0102

  • Engine Efficiency Table load axis extended to 41 sites.
  • Fuel Mixture Aim Clamp lowered to 0.3LA

01.02.0090

  • Anti Lag Shutdown Exhaust Temperature refers to Exhaust Temperature Maximum.
  • Engine Speed Limit Increase and Decrease Rate added. This controls the rate at which the Engine Speed Limit increases or decreases.
  • Engine Overrun Vehicle Speed condition can be ignored by setting Engine Overrun Vehicle Speed Threshold to 0km/h.
  • Gear axis added to Idle Ignition Timing Advance Control Proportional Gain.
  • Exhaust Temperature Boost Limit table axis channel changed to Exhaust Temperature Maximum.
  • Exhaust Temperature Fuel Mixture Aim table axis channel changed to Exhaust Temperature Maximum.
  • Idle Throttle Pedal Blend internally clamped so that the blend point cannot exceed 100%.
  • Idle State can get stuck in Test when Actuator Solenoid Resource is Not in Use bug fixed.
  • Throttle Aim set to NaN from Anti Lag Throttle Aim bug fixed.
  • Throttle Limit Increase and Decrease added. This controls the rate at which the Throttle Limit increases or decreases.
  • System updated to version 1.4.0.97
  • MoTeC Control module updated v1.12.122.
    • Throttle Servo 2 (includes SENT Secure Serial Decode Type) calibration schema added to Dual Throttle Servo and Single Throttle Servo classes.
    • Minimum M1 System version updated to 1.4.0.92.
    • Temperature added to Boost with Servo and Boost with Dual Servo classes.
    • Actuator Fault Duty Cycle & Delay added to drive the Actuator to the fully open position when Actuator Diagnostic reports a fault in the Boost with Servo and Boost with Dual Servo classes.
    • Static Duty Cycle Test added to Single Throttle Servo and Dual Throttle Servo classes.
    • Update Boost Control with Servo class:
      • Servo Activate conditions added.
      • Servo Power Save Delay added.
      • Servo Actuator Test options added.
      • Servo Actuator Model added.
      • Servo Actuator Position Sensor Tracking with limited range support added.
      • Boost Pressure axis added to Servo Actuator Control Feed Forward table.
      • Servo Actuator Control Integral Negative Clamp added.
      • Force close when Aim is 0% to ensure the gate is fully shut. The zero position is tracked at this time to allow for changes due to thermal expansion.
      • Reset servo fault when throttle position is lifted.
      • Auto zero Servo Position Sensor on ECU power up.
      • Servo Temperature added.
      • Servo Actuator Fault Duty Cycle & Delay added to drive the Servo Actuator to the fully open position when Servo Actuator Diagnostic reports a fault.
  • MoTeC Input Module update to v1.10.58.
    • Fix, a NaN value and Diagnostic of Ok could be reported at the same time on power up. Issue affected most classes.
    • Add Diagnostic Delay to Voltage class.
    • Remove 'Diagnostic Delay' validation maximum.
    Migration Notes;
    • If Boost Servo is in use;
      • Set Boost Servo Default Overrun Position. Typically 0% to assist holding or building boost during overrun conditions.
      • Configure Boost Servo Actuator Control Feed Forward if Boost Servo is in use. Initially this table can be setup with two axis sites (Boost Servo Actuator Aim = 0 and 100%). At Boost Servo Actuator Aim = 0% set the table value to equal Boost Servo Actuator Control Feed Forward Offset from the original package. At Boost Servo Actuator Aim = 100% set the table value to equal Boost Servo Actuator Control Feed Forward Gain + Boost Servo Actuator Control Feed Forward Offset from the original package.
      • Set Boost Servo Actuator Control Integral Negative Clamp to equal Boost Servo Actuator Control Integral Minimum from the original package.
      • Confirm Boost Servo Actuator Position closely follows the Boost Servo Actuator Aim when performing a step test using Boost Servo Actuator Test.

01.02.0085

  • MoTeC OE SeaDoo RXTX module updated to v 1.0.20
    • Alternate CAN messages added.
    • Throttle Position 1-5 added.
    • Brake Gear renamed to Brake State
    • Brake Gear added with a firmware resource that can be used for Gear Position.

01.02.0083

  • Jet Reverse Bucket Servo Function added

01.02.0079

  • MoTeC OE SeaDoo RXTX module updated to v 1.0.17
    • CAN OE Integration Updates for the 2021 and 2022 models.

01.02.0076

  • Pressure Sensors added for, Jet Nozzle Presure, Jet Stator Pressure, Jet intake starboard and port pressure.
  • Jet Reverse Bucket Function added.

01.02.0056

  • Speed Only Engine Output Test added.
  • MoTeC OE SeaDoo RXTX module updated to v 1.0.14
    • CAN Updates.

01.02.0054

  • System updated to version 1.4.0.91
  • Support for Batch Fire fuel injection added.
  • GPS via RS232 functionality added for M130 (Rev Q+) and M122 ECU's.
  • MoTeC GPS Module update to v1.7.21.
    • Serial Port Resource and Baud rate can be set externally.
    • Update system version to 1.4.0.0091.
    • Add support for M130 Rev Q. hardware with RS232 Rx on Udig 6 and 7.
    • Moves the serial port setup inside the GPS group.
    • Ensure a Diagnostic of Invalid Interface is reported correctly for all hardware types.
    • Allow any CAN Decode message to set the Diagnostic to OK. Allows GPS Speed message to be received by itself for example.
    • Help Updates.
  • MoTeC Fuel Module update to v1.18.1
    • System update to 1.4.0.91.
    • Allowance for Revolution Lock and Cylinder Lock Engine Speed Reference State in Single, Double, Triple and Quadruple Injector Fuel Volume classes. Required for Batch Fire Injection.
  • MoTeC Input Module update to v1.10.36.
    • Remove 'Diagnostic Delay' validation maximum.
    • Resource re-ordered in latchable switch class.
  • MoTeC Comms Module updated to 1.10.3
    • System updated to v1.04.0091.
    • Serial Port class removed.
    Migration Notes:
    • Set GPS Serial Port Resource and GPS Serial Port Baud if GPS Interface is RS232 Port.

01.02.0050

  • Cruise updated.
  • No Wake updated.
  • Vehicle Speed Limit added.
    • Migration Notes:
    • Set Cruise Enable Throttle Lever Hysteresis to Cruise Throttle Lever Hysteresis from the old package.

01.02.0046

  • Race Time axis added to Fuel Mixture Aim Trim.

01.02.0045

  • Engine Start updated.

01.02.0042

  • Driver Engine Speed Limit Switch converted to 3 position switches.
  • Driver Ignition Timing Main Switch axis added to Ignition Timing Trim Main table.

01.02.0040

  • Ignition Timing Trim Main added.

01.02.0039

  • Driver Fuel Mixture Aim and Driver Ignition Timing Main Switches converted to 3 position switches.

01.02.0038

  • Engine Run updated to be disabled by Engine Start Switch when Type is Push Button.

01.02.0036

  • Vehicle Tip Over updated to include a delay.

01.02.0035

  • MoTeC OE SeaDoo RXTX module updated to v 1.0.12
    • RXTX 2018 and 2019 models added.
  • Throttle Aim set to Idle while Seadoo Braking.
  • Gear Shift Mode bug fixed.
  • Vehicle Speed Limit from Seadoo Cruise added.
  • Vehicle Tip Over Warning removed.
  • Engine Start updated.

01.02.0029

  • Engine Start Delay added.

01.02.0028

  • Throttle Limit added to all Warnings.

01.02.0025

  • Throttle Servo Fault Engine Speed Limit applied when Throttle Servo Bank N Diagnostic is Power Save.
  • LTC enable strategy improved to better suit marine applications.
  • Gear Source added.
  • Engine Run Time Reset Value added.

01.02.0018

  • Engine Oil Temperature Estimate available when sensor is not in use.
  • Engine Oil Pressure Low Switch updated.

01.02.0017

  • Fuel Tank Level Warning and Warning Light added.

01.02.0016

  • Engine Oil Pressure Low Switch Engine Speed Minimum and Hysteresis added.

01.02.0015

  • Engine Start updated.
  • Engine Stop updated.
  • Engine Oil Pressure Low Switch updated.

01.02.0010

  • Forward 2 removed from Gear.

01.02.0006

  • Vehicle speed updated.

01.02.0004

  • M1 General 0x640 CAN Template reverted to version 5.
  • M1 General 0x650 CAN Template reverted to version 5.
  • M1 General 0x6A0 CAN Template reverted to version 1.
  • Engine Stop Switch bug fixed.
  • Engine Starter Motor renamed to Engine Start Motor.
    • Migration Notes:
    • Update any M1_General_0x640 CAN templates to M1_General_0x640_Version 5.
    • Update any M1_General_0x650 CAN templates to M1_General_0x650_Version 5.
    • Update any M1_General_0x6A0 CAN template to M1_General_0x6A0_Version 1.

01.02.0003

  • Coolant Pump added.
  • Engine Start updated.
  • Engine Starter Motor updated.
  • Engine Stop Switch added.

01.02.0002

  • System updated to version 1.4.0.79.
  • ADR added.
  • Airbox Mass Flow added.
  • Airbox Temperature Sensor Resource object name changed from Airbox Temperature Sensor Voltage Resource.
  • Airbox Temperature Sensor updated
  • Airbox Pressure added.
  • Alternative Fuel added.
  • Alternator added.
  • Ambient Pressure updated
  • Ambient Temperature updated
  • Anti Lag updated
  • Anti Cavitation Mode enumeration changed. 'Disabled' value changed to 'Not in Use' to allow for hiding of unused objects.
  • Anti Cavitation Throttle Limit object name changed from Anti Cavitation Throttle.
  • Anti Cavitation Ignition Timing Trim object name changed from Anti Cavitation Ignition Timing Compensation.
  • Auxiliary Output 1-4 Resource object name changed from Auxiliary Output 1-5 Pulse Width Modulation Resource.
  • Auxiliary Output 1-4 Test added.
  • Auxiliary Output 1-4 Frequency added.
  • Auxiliary Output 1-4 Duty Cycle table validation limit minimum increased to -100%
  • Auxiliary Output 1-4 Activate Vehicle Speed added.
  • Auxiliary Output 1-4 Output object name changed from Auxiliary Output 1-5 Pulse Width Modulation.
  • Auxiliary Output 1 Ignition Timing Trim object name changed from Auxiliary Output 1 Ignition Timing Compensation.
  • Auxiliary Output 1 Fuel Volume Trim object name changed from Auxiliary Output 1 Fuel Volume Compensation.
  • Auxiliary Output 1 Fuel Mixture Aim added. Replaces Auxiliary Output 1 Fuel Mixture Compensation
  • Auxiliary Output 5 added.
  • Brake State added.
  • Boost updated
  • Cruise object name changed from Cruise Assist.
  • Cruise Mode enumeration changed. Paramaterd 'Disabled' value changed to 'Not in Use' to allow for hiding of unused objects.
  • Cruise Throttle object name changed from Cruise Assist Throttle.
  • Cruise Throttle Lever Hysteresis object name changed from Cruise Assist Throttle.
  • Cruise enable conditions updated to include Brake State
  • CAN Bus 1 object name changed from Communications CAN Bus.
  • Coolant Temperature Sensor updated
  • Coolant Temperature Warning updated
  • Coolant Temperature Estimate added.
  • Coolant Temperature Engine Speed Limit added.
  • Coolant Temperature Ignition Timing Compensation table axis modified. Coolant Temperature axis sites reduced to 11. Engine Load Normalised axis added.
  • Coolant Temperature Fuel Volume Compensation table axis modified. Coolant Temperature axis sites reduced to 11.
  • Coolant Temperature Fuel Mixture Aim added. Replaces Coolant Temperature Fuel Mixture Compensation
  • Coolant Temperature Boost Limit added. Replaces Coolant Temperature Boost Aim Compensation
  • Coolant Pressure added.
  • Driver Switches added.
  • Driver Anti Lag Switch object name changed from Anti Lag Switch.
  • Driver Cruise Set Switch object name changed from Cruise Assist Set Button.
  • Driver Cruise Up Switch object name changed from Cruise Assist Up Button.
  • Driver Cruise Down Switch object name changed from Cruise Assist Down Button.
  • E8XX added.
  • ECU CPU Usage added.
  • ECU Acceleration updated
  • ECU Acceleration X Sensor object name changed from ECU Acceleration X.
  • ECU Acceleration Y Sensor object name changed from ECU Acceleration Y.
  • ECU Acceleration Z Sensor object name changed from ECU Acceleration Z.
  • ECU Battery updated
  • ECU Power Relay updated
  • ECU Sensor & Internal voltages updated
  • ECU Receive updated
  • ECU Receive object name changed from Communications Receive.
  • ECU Transmit updated
  • ECU Transmit CAN Bus object name changed from Communication CAN Bus.
  • Engine Trip Time added.
  • Engine Efficiency Boost Pressure Compensation added.
  • Engine Efficiency Airbox Pressure Compensation added.
  • Engine Charge Temperature added.
  • Engine Charge Cooling updated
  • Engine Charge Cooling Gain Primary object name changed from Engine Charge Cooling Gain.
  • Engine Load Normalised added.
  • Engine Speed Limit Maximum table axis modified. X axis changed to Driver engine Speed Limit Maximum Switch
  • Engine Speed Limit Warning updated
  • Engine Synchronisation Resource added.
  • Engine Synchronisation Ignore and State added.
  • Engine Run added.
  • Engine Start Stop Switch object name changed from Engine Start Stop Button.
  • Engine Start Stop Switch updated
  • Engine Starter Motor object name changed from Starter Motor.
  • Engine Starter Motor Relay Resource object name changed from Starter Motor Relay Output Resource.
  • Engine Starter Motor Relay updated
  • Engine Crank Idle Mass Flow added.
  • Engine Crank Flooded Throttle Position added.
  • Engine Crank Fuel Volume Compensation object name changed from Fuel Volume Compensation Cranking.
  • Engine Post Start Idle Aim Compensation added.
  • Engine Post Start Idle Mass Flow Feed Forward added.
  • Engine Post Start Fuel Volume Compensation object name changed from Fuel Volume Compensation Post Start.
  • Engine Oil Temperature Sensor Resource object name changed from Engine Oil Temperature Sensor Voltage Resource.
  • Engine Oil Temperature Estimate added.
  • Engine Oil Temperature Engine Speed Limit added.
  • Engine Oil Temperature Sensor updated
  • Engine Oil Temperature Warning updated
  • Engine Oil Pressure Sensor updated
  • Engine Oil Pressure Low Switch updated
  • Engine Oil Pressure Warning updated
  • Engine Oil Level added.
  • Engine Temperature added.
  • Engine Overrun updated
  • Engine Crankcase added.
  • Engine Boost Limit added.
  • Engine Mode Switch removed. Replaced by Driver Fuel Mixture Aim Main Switch, Driver Ignition Timing Main Switch, Driver Engine Speed Limit Maximum Switch and Driver Throttle Lever Translation Switch.
  • Exhaust Lambda Bank 1 & 2 added.
  • Exhaust Lambda Warning added.
  • Exhaust Lambda External removed. Use Exhaust Lambda Collector instead.
  • Exhaust Lambda Collector CAN Bus added. Replaces Exhaust Lambda Collector Mode
  • Exhaust Lambda Cylinder 1-3 CAN Bus added. Replaces Exhaust Lambda Cylinder 1-3 Mode
  • Exhaust Pressure added.
  • Exhaust Temperature Maximum added.
  • Exhaust Temperature Boost Limit added. Replaces Exhaust Temperature Boost Limit Compensation
  • Exhaust Temperature Fuel Mixture Aim added. Replaces Exhaust Temperature Fuel Mixture Compensation
  • Exhaust Temperature Ignition Timing Compensation removed. Replaced by Engine Load Average Ignition Timing Trim.
  • Exhaust Temperature Bank 1 & 2 added.
  • Exhaust Temperature Collector Sensor Resource object name changed from Exhaust Temperature Collector Sensor Voltage Resource.
  • Exhaust Temperature Collector Sensor updated
  • Exhaust Temperature Cylinder 1-3 Sensor Resource object name changed from Exhaust Temperature Cylinder 1-3 Sensor Voltage Resource.
  • Exhaust Temperature Cylinder 1-3 Sensor updated
  • Exhaust Camshaft added.
  • Exhaust Muffler Temperature object name changed from Muffler Temperature.
  • Exhaust Muffler Temperature Sensor Resource object name changed from Muffler Temperature Sensor Voltage Resource.
  • Exhaust Muffler Temperature Sensor updated
  • Exhaust Muffler Temperature Warning updated
  • Fuel Used Primary Correction added.
  • Fuel Properties Calibration added.
  • Fuel Mixture Aim Main object name changed from Fuel Mixture Aim A.
  • Fuel Mixture Aim Compensation removed. No longer required.
  • Fuel Mixture Aim State added.
  • Fuel Volume Bank 1 & 2 added.
  • Fuel Volume Transient removed. Replaced by Fuel Film.
  • Fuel Mixture Aim B removed. Replaced by Fuel Mixture Aim Main and Driver fuel Mixture Aim Main Switch.
  • Fuel Timing Primary object name changed from Fuel Timing.
  • Fuel Timing Primary Main table axis modified. Engine Speed axis sites reduced to 11. Y axis changed to Inlet Manifold Pressure.
  • Fuel Timing Primary Limit table axis modified. Engine Speed axis sites reduced to 11.
  • Fuel Flow Supply & Return added.
  • Fuel Film added.
  • Fuel Temperature Estimate added.
  • Fuel Temperature Sensor updated
  • Fuel Pressure Estimate added.
  • Fuel Pressure Default added.
  • Fuel Pressure Control added.
  • Fuel Pressure Regulator Type added. Replaces Fuel Pressure Sensor Type & Regulator Reference
  • Fuel Pressure Regulator Ratio added. Replaces Fuel Pressure Sensor Type & Regulator Reference
  • Fuel Pressure Sensor updated
  • Fuel Pressure Warning updated
  • Fuel Water Content added.
  • Fuel Injector Primary updated
  • Fuel Pump updated
  • Fuel Pump 2 & 3 added.
  • Fuel Closed Loop Mode enumeration changed. 'Disabled' value changed to 'Not in Use' to allow for hiding of unused objects.
  • Fuel Closed Loop Activate Throttle Pedal added.
  • Fuel Cut. added. Replaces Fuel Diagnostic
  • Fuel Composition added.
  • Fuel Composition Boost Limit added.
  • Fuel Tank added. Replaces Fuel Level
  • Fuel Cylinder 1-3 Primary Output Resource object name changed from Fuel Cylinder 1-3 Output Resource.
  • Fuel Cylinder 1-3 updated
  • Gear added.
  • GPS updated
  • Idle added. Replaces Idle Throttle
  • Ignition Test added.
  • Ignition Cut added.
  • Ignition Coil Calibration added.
  • Ignition Coil Charge object name changed from Ignition.
  • Ignition Driver Firing Edge added.
  • Ignition Cylinder 1-3 updated
  • Ignition Cylinder 1-3 Resource object name changed from Ignition Cylinder 1-3 Output Resource.
  • Ignition Output Cut Pattern added.
  • Ignition Diagnostic removed. Replaced by Engine Run.
  • Ignition Switch removed. replaced by Engine Run Switch.
  • Ignition Timing Stop Edge removed. No longer required.
  • Inlet Air Temperature object name changed from Inlet Manifold Temperature. Replaces Inlet Manifold Temperature
  • Inlet Air Temperature Boost Limit added. Replace Inlet Manifold Temperature Boost Limit Compensation
  • Inlet Air Temperature Fuel Mixture Aim added. Replaces Inlet Manifold Temperature Fuel Mixture Aim Compensation
  • Inlet Manifold Pressure Mode added.
  • Inlet Manifold Pressure Estimate added.
  • Inlet Manifold Pressure Sensor updated
  • Inlet Manifold Pressure Warning added.
  • Inlet Manifold Pressure Correction added.
  • Inlet Manifold Temperature updated
  • Inlet Manifold Flap added.
  • Inlet Manifold Runner added.
  • Inlet Camshaft added.
  • Intercooler added.
  • Cruise Mode enumeration changed.
  • Knock Threshold table axis modified. Engine Speed and Engine Load Normalised axes sites reduced to 11. Fuel Composition axis added
  • Knock Recovery Rate table axis modified. Engine Speed axis sites reduced to 11. Engine Load Normalised axis added
  • Knock Activate added.
  • Knock Trim Gain table axis modified. Fuel Composition axis added.
  • Knock Window DSP object name changed from Knock Window Output.
  • Knock Warning updated
  • Knock Cylinder 1-3 added.
  • Knock Cylinder 1-3 Gain object name changed from Engine Cylinder 1-3.
  • Jet Nozzle Pressure Sensor Resource object name changed from Jet Nozzle Pressure Sensor Resource.
  • Jet Nozzle Pressure Sensor updated
  • Jet Nozzle Angle Horizontal Sensor Resource object name changed from Jet Nozzle Angle Horizontal Sensor Resource.
  • Jet Nozzle Angle Horizontal Sensor updated
  • Jet Intake Pressure Sensor Resource object name changed from Jet Intake Pressure Sensor Resource.
  • Jet Intake Pressure Sensor updated
  • Jet Intake Temperature object name changed from Water Temperature.
  • Jet Trim Sensor Resource object name changed from Jet Trim Sensor Resource.
  • Jet Trim Sensor updated
  • Lap added.
  • Lanyard Switch updated
  • Lanyard added.
  • Launch Engine Speed table axis modified. Driver Launch Aim switch axis added
  • Launch Fuel Volume Trim object name changed from Launch Fuel Volume Compensation.
  • Launch Switch removed. Replaced by Driver Launch Switch
  • Logging throttle Lever added.
  • Logging Engine Speed added.
  • Logging Unload added.
  • LTC added.
  • LTC Power Save Delay object name changed from Exhaust Lambda Power Save Delay.
  • Nitrous added.
  • No Wake object name changed from No Wake Mode.
  • No Wake Mode added.
  • No Wake Enable added.
  • No Wake Throttle Aim object name changed from No Wake Mode Throttle.
  • PDM added.
  • Race Time Mode added.
  • Race Time Mode updated
  • Race Time Activate Vehicle Speed added.
  • Race Time Activate Delay added.
  • Race Time Reset added.
  • Race Time Boost Limit added. Replaces Race Time Boost Limit Compensation
  • Race Time Fuel Mixture Aim added. Replace Race Time Fuel Mixture Aim Compensation
  • Race Time Ignition Timing Trim object name changed from Race Time Ignition Timing Compensation.
  • Race Time Throttle Limit added. Replaces Race Time Throttle Lever Compensation
  • SeaDoo CAN Bus added.
  • SeaDoo Model object name changed from Communications SeaDoo Model.
  • SeaDoo ADL Diagnostic object name changed from Communications ADL Diagnostic.
  • SeaDoo Brake object name changed from Brake.
  • SeaDoo GPS object name changed from Communications GPS.
  • SLM added.
  • Steering Angle added.
  • Steering Force added.
  • Steering Pressure added.
  • Steering Lock Switch Resource object name changed from Steering Lock Switch State Resource.
  • Steering Lock Switch updated
  • Steering Lock Throttle Aim object name changed from Steering Throttle.
  • Tachometer added.
  • Throttle Area table axis modified. Throttle Servo Position axis sites increased to 41
  • Throttle Lever Sensor Main Resource object name changed from Throttle Lever Sensor Main Voltage Resource.
  • Throttle Lever Sensor Tracking Resource object name changed from Throttle Lever Sensor Tracking Voltage Resource.
  • Throttle Lever Translation table axis modified. Engine Speed axis sites reduced to 21. Driver Throttle Lever Translation Switch axis added.
  • Throttle Lever Sensor updated
  • Throttle Lever Compensation removed. Replaced by Throttle Limit.
  • Throttle Limit added.
  • Throttle Aim Diagnostic added.
  • Throttle Aim Minimum added.
  • Throttle Cranking removed. Replaced by Throttle Aim Minimum and Idle control system
  • Throttle Dashpot removed. Replaced by Idle control system
  • Throttle Position Fuel Mixture Aim added.
  • Throttle Position Estimate added.
  • Throttle Position Sensor added.
  • Throttle Servo updated
  • Throttle Test updated
  • Turbocharger added.
  • VCS added.
  • Vehicle Speed updated
  • Vehicle Acceleration Lateral Sensor Resource object name changed from Vehicle Acceleration Lateral Sensor Voltage Resource.
  • Vehicle Acceleration Lateral Sensor updated
  • Vehicle Acceleration Longitudinal Sensor Resource object name changed from Vehicle Acceleration Longitudinal Sensor Voltage Resource.
  • Vehicle Acceleration Longitudinal Sensor updated
  • Vehicle Acceleration Vertical Sensor Resource object name changed from Vehicle Acceleration Vertical Sensor Voltage Resource.
  • Vehicle Acceleration Vertical Sensor updated
  • Vehicle Tip Over Switch updated
  • Vehicle Tip Over Switch Resource object name changed from Vehicle Tip Over Switch State Resource.
  • Vehicle Tip Over Warning updated
  • Warning Source added.
  • Warning Mode added.
  • Wastegate added.
    • Migration Notes:
    • Refer to migration document for this version.

Previous Version (01.01.0022)

Package Notes

Related Software
Versions
Version
01.02.0144