Package GPR Rotary (M130).April 2019 "Throttle Based Start File v8"

Current Version (1.01.0040)

• MoTeC OE Mazda RX8 2004 module update to v1.0.20
• Communications Receive added with help for setting firmware resources.
• Communications Temperature Gauge added.
• Trip Meter added.
• Engine Oil Pressure Warning and Engine Oil Level Warning sent to dash
• Engine check light activated by Warning Source.
• CAN receive wheel speeds updated
• Fuel Rotor 2 Quick Lambda bug fixed.
• Fuel Rotor N Quaternary Film bug fixed.

1.01.0039

• Engine Oil Metering pump bug fixed.

1.01.0037

• Battery Voltage, Fuel Composition, Transmission Temperature and Differential Temperature Warnings added.

1.01.0035

• Coolant Fan 1 & 2 Enable Battery Voltage added. To disable fan operation when the Battery Voltage drops below a set threshold.
• Coolant Fan 1 & 2 Enable Engine State Override added. To enable fan operation when the engine is not running.
Migration Notes;
• If Coolant Fan 1 is in use, set Coolant Fan 1 Enable Battery Voltage Threshold and Coolant Fan 1 Enable Battery Voltage Hysteresis.
• If Coolant Fan 2 is in use, set Coolant Fan 2 Enable Battery Voltage Threshold and Coolant Fan 2 Enable Battery Voltage Hysteresis.

1.01.0034

• MoTeC Fuel module updated to version 1.17.42.
• Enable conditions made external in Port Injector Rotary class.
• MoTeC Warning module updated to v 1.4.15
• Count limit added which activates any of the configured warning limits while the count is above the count limit.
Migration Notes;
• Set Fuel Injector Primary Volume Hysteresis.
• Set Fuel Injector Secondary Volume Hysteresis if in use.
• Set Fuel Injector Tertiary Volume Hysteresis if in use.

1.01.0025

• Inlet Air Temperature validation limits removed.
• Inlet air Temperature axis added to Engine Charge Cooling Primary, Secondary and Tertiary.
• Gear Fuel Volume Compensation added.
Migration Notes;
• Set Gear Fuel Volume Compensation to 0%Trim

1.01.0019

• MoTeC OE Mazda RX8 2004 module update to v1.0.18
• CAN messages updated.
• EPS Enable simplified.

1.01.0016

• Cruise Control added.
• MoTeC OE Mazda RX8 2004 module update to v1.0.9
• EPS CAN messages updated.
• Cruise CAN messages added.
• MoTeC Input module updated v1.10.25.
• Improve Dual Driven Wheel Speed efficiency and diagnostic reporting (for Cruise control).
• Fix Latchable Switch Value Storage type public properties lost in v1.10.0022.
• Driver Switches must be active for two consecutive samples.

1.01.0014

• MoTeC OE Mazda RX8 2004 module update to v1.0.8
• CAN messages updated.

1.01.0010

• Driver Fuel Mixture Aim Switch axis added to Alternative Fuel Mixture Aim.
• Driver Ignition Timing Main Switch axis added to Alternative Fuel Ignition Timing.
• Boost Control Feed forward Offset, Compensation and Maximum Change Rate set to constants.
• Bosch ABS M4 update to Bosch ABS (M4 & M5)
• Clutch Slip calculated using speed difference instead of ratio difference.
• Various event rate updates including Brake Switch, Brake Vacuum Pump, Clutch Position, Clutch Switch, Crankcase Pressure, Engine Oil Pressure, Lambda, Idle Mass Flow Feed Forward, Nitrous Reset, Nitrous Stage 1 and 2, Nitrous Bottle, Throttle Position Fuel Mixture Aim, Transmission Pressure.
• Default positions set for Driver Switches when Not in Use.
• Engine Run Switch Condition added to ECU Power Relay.
• Engine Run Time updated every 8s instead of every 1s.
• Inlet Manifold Pressure 100kPa added to Engine Load Normalised.
• Fuel Injector Primary/Secondary/Tertiary Duty Cycle Warning added.
• Gear Input, Output Ratio consistency improved.
• Gear Output Shaft Speed Sensor Removed.
• Idle Mass Flow Feed Forward Minimum table added.
• Transmission Brake Switch moved to Driver Transmission Brake Switch.
• Coolant Temperature axis added to Ignition Timing Leading and Trailing.
• Nitrous Active and Reset Engine Speed Limit changed to Engine Speed Limit Nominal.
• Nitrous Reset Engine Speed Threshold replaced with Minimum and Maximum.
• Nitrous Stage 1 and 2 Inlet Manifold Pressure Threshold replaced with Minimum and Maximum.
• Fuel Volume Compensation due to Nitrous based modified to be based on Fuel Mass Flow and Nitrous Bottle Pressure.
• Nitrous Bottle Pressure Warning added
• Race Time in use conditions modified.
• Throttle Limit for Fuel Injector Primary, Secondary and Tertiary Duty Cycle Warning added.
• Vehicle Drive Circumference and Ratio changed to channels.
• Vehicle Speed GPS Update validation improved.
• Warning Clutch Position Diagnostic added.
• Speed axis added to Wheel Speed Front and Rear Circumference.
• Gear Ratio application to Output Shaft Speed bug fixed
• Fuel Composition Sensor Tranmited from ECU (0x671) instead of Fuel Composition.
• Alternative Fuel Pressure Boost Limit added.
• All Ignition Timing limits ignored when Igntion Timing Test is Check Timing.
• Nitrous Bottle Pressure Default added.
• Nitrous Bottle Pressure Fuel Mass Flow Trim removed from Fuel Volume calculation when not in use.
• Alowance for A and B primary, secondary and tertiary injector. Both A and B use the same injector settings with the alocated fuel divides evenly amongs the injectors.
• Alternative Fuel can be independently applied to the secondary and tertiary injectors
• Fuel Injector Peak Time changed not requesting restart bug fixed.
• System upgraded to version 1.4.0.66
• MoTeC Control module updated to version 1.12.70.
• Warnig module updated.
• Add Boost Pressure Default and change the fallback strategy for Boost Pressure in Boost Control and Boost Control with Servo classes.
• Fix Boost Maximum when using a Boost Pressure Sensor in Boost Control and Boost Control with Servo class.
• Boost Pressure Warning enabled when Boost Pressure is above Boost Activate (previously was enabled when above 0) in Boost Control, Dual Boost Control Class and Boost Control with Servo classes.
• Pressure Warning added to all Boost Control classes.
• Input tags removed from Throttle Servo classes.
• Add 'Limited' enumeration to the Boost Aim State. To be set when the boost limit is influencing the Boost Aim.
• Servo Actuator Motor Output must be active to run update.
• Servo Linearisation X-Axis fixed to Control.
• MoTeC Fuel module updated to version 1.17.19.
• Allowance for A and B injectors in the Triple Injector Fuel Volume class.
• Bosch OE Integration module updated to version 1.0.21.
• Removed the writing of Firmware resources 29, 30 and 31 which is ABS Active, ABS Lamp and EBD Lamp.
• Removed Roll Acceleration channel.
• Yaw Acceleration only written if M4 is selected.
• Revised CAN receive method to improve efficiency.
• Revised CAN transmit method (no change in functionality).
• Fixed firmware 27 write, had Yaw Rate, should have been Roll Rate.
• Added ABS Switch Position Index data type to the public properties.
• Wiper LIN messaging corrected.
• System updated to version 1.4.0.61.
• MoTeC Input module added.
• Firmware resources modified in Bosch ABS class.
• Stoped Bosch ABS class writing to Firmware Resources when CAN Bus is Not in Use.
• ABS Position Switch added to Bosch ABS class added. This position switch is transmitted vie CAN to the Bosch ABS (M5 Only) module.
• Bosch ABS class added. This supersedes Bosch ABS M4 class.
• Type parameter added to Bosch ABS class. This type parameter allows users to select between Bosch M4 and M5 ABS units.
• Extra CAN messaging for Bosch M5 ABS unit added to Bosch ABS class.
• ABS Position Switch added to Bosch ABS class added. This position switch is transmitted vie CAN to the Bosch ABS (M5 Only) module.
• MoTeC Input module updated to version 1.10.23.
• Old Name cleared from all Resources.
• Latchable Switch class modified to improve migration from Universal Switch class.
• Engine Speed parameter for Turbocharger Speed class Diagnostic added.
• Diagnostic public properties can be set externally on Voltage class.
• Pressure sensor may use Hybrid resource
• Add Mass Air Flow type with Hybrid resource (requires Schema update from MoTeC Online)
• Add Mapping Not in Use to Indexed switch, used when Index is Not in Use.
• Add Index of Default to Indexed Switch, allows Mapping Default to set the switch value manually.
• MoTeC Comms module updated to version 1.10.02.
• Not in Use added to Serial Port class.
• MoTeC Output module updated to version 1.9.8.
• Hold minimum validation set to 0 in Fuel Pump Relay class.
• Switched output, expose Allowed Events.
• MoTeC Wastegate Pressure Control module updated to version 1.3.13.
Migration Notes;
• Set the Boost Pressure Default, if the Boost system is in use.
• If the Bosch ABS M4 was previously in use, ensure that any Firmware Resources are correct as some have changed. See Bosch ABS for Firmware resource allocation.
• Set Driver Transmission Brake Switch if the Transmission Brake Switch was previously in use.
• Set Fuel Used Primary Correction and Fuel Used Secondary Correction.
• Set Idle Mass Flow Feed Forward Minimum if the Idle system is in use.
• If the Nitrous system is in use;
• Set Nitrous Reset Engine Speed Minimum and Nitrous Reset Engine Speed Maximum.
• Set Nitrous Stage 1 Override Inlet Manifold Pressure Minimum and Nitrous Stage 2 Override Inlet Manifold Pressure Minimum.
• Set Nitrous Stage 1 Override Inlet Manifold Pressure Maximum and Nitrous Stage 2 Override Inlet Manifold Pressure Maximum.
• Set Nitrous Stage 1 Fuel Mass Flow and Nitrous Stage 2 Fuel Mass Flow. This replaces Nitrous Fuel Volume Compensation.
• Set Turbocharger Bank 1 Speed Diagnostic Engine Speed, if the Turbocharger Bank 1 Speed Sensor is in use.
• Set Turbocharger Bank 2 Speed Diagnostic Engine Speed, if the Turbocharger Bank 2 Speed Sensor is in use.
• Set Wastegate Pressure Actuator Increase Minimum and Wastegate Pressure Actuator Decrease Minimum, if the Wastegate Pressure Actuator is in use.
• Set the RS232 Baud Rate to Not in Use, if RS232 is not in use.
• If Alternative Fuel is used as the only fuel for both the secondary and tertiary injectors (i.e. Alternative Fuel Mode was set to Secondary Fuel) set Fuel Injector Secondary Alternative Fuel to Enabled and Fuel Injector Tertiary Alternative Fuel to Enabled.

1.00.0031

• Engine Efficiency maximum validation limit increased.
• All Temperature Hysteresis Quantities changed to Temperature Delta.
• Gear Shift Timing not updated bug fixed.
• MoTeC Fuel module updated to 1.17.18
• Secondary Fuel Conversion factor bug fixed in Port Injector Rotary and Port Injector Saturated class.
• Enrichment and Enleament added Positive and Negative in Transient Fuel Class.
• Activate Throttle Pedal added to Angle and Dual Closed Loop class.
• Duty Cycle Warning added to Port Injector Rotary and Port Injector Saturated class.
• Maximum Validation Limit removed from Fault Delay of Fuel Closed Loop Classes.
• Fuel Closed Loop going into fault after long overrun bug fixed.
• MoTeC Coolant Fan module updated to v 1.6.4
• Enable Coolant Temperature Hysteresis changed to Temperature Delta.
• MoTeC Warning module updated to v 1.4.12
• Hysteresis Quantity and Display Unit can be set independent of Minimum and Maximum.
• Warning Minimum Hysteresis validation bug fixed
• Add Throttle Limit option to warning.
• Fixed behaviour if warning re-actives before the reset delay expires (stays in Limit)
• Changed behaviour, the activate and limit delays are applied only after the system is enabled.
• MoTeC OE Mazda RX8 2004 v1.0.5
• Warning and Cruise modules replaced with data type public property.
Migration Notes;
• Ensure all Temperature Hysteresis channels are set correctly.
• Ensure all Fuel Volume Transient Settigns are set correctly.

1.00.0026

• Ignition Timing Trailing Limit Relative Minimum, Relative Maximum, Advance and Retard added.
• MoTeC Ignition module updated to 1.11.0011
• Trailing Limit Relative Minimum, Relative Maximum, Advance and Retard added to Dual Rotary Spark Plug with knock class.
• Ignition Timing Object input category can be set externally.
• Throttle reduction on upshifts with recovery added to Gear Shift.
• Extended Gear Shift clutch disengaged calculation.
Migration Notes;
• Set Ignition Timing Trailing Limit Relative Minimum and Ignition Timing Trailing Limit Relative Maximum.
• Set Ignition Timing Trailing Limit Advance and Ignition Timing Trailing Limit Retard.
• Set Gear Shift Throttle Aim settings, if in use.

1.00.0021

• Build 1.4.1.109+ Help XML Formatting and Compile Options.
• GPR Rotary (M170 and M190) configurations added.
• Gear Shift State Calculation updated to match GPR v1.7.5.

1.00.0015

• Rotary Master Project created.
• Package upgrades updated.
• System upgraded to version 1.4.0.56.
• MoTeC Bosch OE Integration module upgraded to version 1.0.0006.
• MoTeC Control module upgraded to version 1.12.0046.
• MoTeC LTC module upgraded to version 1.9.0002.
• MoTeC Wastegate Pressure Control module upgraded to version 1.3.0011.
• Tertiary injectors with secondary fuel calculation modified to only allow secondary fuel on tertiary injectors if secondary injectors are configured.
• Coolant Dual Speed Fans moved to Mazda group
• M1 Transmit 0x650 message (Driver Switches) added.
• Engine Number of Rotors changed to Engine Rotors.
• Diagnostic condition removed from Engine Speed Limit calculation.
• Ignition Timing Limit Advance changed to Ignition Timing.
• Ignition Timing Trailing updated to include Ignition Timing Leading Trim when in relative mode.
• Ignition Rotor 1-4 Leading and Trailing Trim Main table axes corrected.
• Warning Mode CAN Bus 2 and 3 Diagnostic added.
• MoTeC Mazda RX8 module upgraded to version 1.0.0004.
• Driver Switch Index Enumeration.
• Knock Trim Enable added.

1.00.0011

• MoteC Ignition module updated to 1.11.0005
• Knock indication only state added.
• Increased validation limits on ignition timing parameters.
• Disabled sensor compensation, trims and boost limits when sensors are set to Not in Use.

1.00.0010

• Gear Input and Output shaft speed sensors added.
• Turbocharger Bank 2 Pressure added.
• Trailing Ignition Timing (when in Overrun, Launch, Anti Lag, Idle or Gear Shift Ignition Retard modes) bug fixed.

1.00.0009

• Transient Fuelling added (Fuel Volume Transient).
• Engine speed limiting disabled when sensors are not ok.
• Turbocharger Bypass Threshold converted to a table with Vehicle Speed, Race Time and a Driver Switch as axes.
• Separate Ignition Driver Firing Edge for both leafing and trailing ignitions.
• MoTeC Ignition module update to 1.11.0004.
• MoTeC Fuel module update to 1.17.0001.
• Mazda RX8 OE Integration CAN option to only enable CAN messages for Electronic Power Steering.
• Fuel Injector SSV Enable ignored if SSV is not in use.
• Fixed bug were both secondary and tertiary injectors were firing on engine output test (when tertiary was selected).
• Separate rotor trims for both leading and trailing ignitions added.
• Engine output test modified to have separate test modes for leading and trailing ignitions.

1.00.0008

• Tertiary fuel added to Fuel Vol Per Cycle.

1.00.0007

• Initial Beta Release.