We use cookies on this site

< Sea-Doo RXT-X 2010.October 2013

Package Sea-Doo RXT-X 2010.October 2013 "RXTX RXPX Stock inj Stock FP 98 Octane 8350 Rev F Adaptor Update"

Sea-Doo RXT-X 2010.October 2013
RXTX RXPX Stock inj Stock FP 98 Octane 8350 Rev F Adaptor Update
Sea-Doo RXT-X 2010.October 2013
01.01.0023
27/05/2022

Make Model Model Year Target Integration Type
Sea-Doo RXTX RXPX 2010 - 2018 PWC Vehicle Custom Plug-In ECU



Release Notes

Current Version (01.01.0023)

  • Launch Engine Speed Limit Margin bug fixed.

01.01.0022

  • Launch remains enabled after Launch Switch is turned off, until end of Launch Engine Speed table.

01.01.0019

  • Launch system operates like GPR

01.01.0018

  • Updates to cover 2016 and later models
  • Power Relay controlled by ECU.
  • Throttle not enabled if ECU Power Relay not on - prevents fuse damage.

01.01.0007

  • Fix CAN Speed transmit in 2007 & 2004 Models.

01.01.0005

  • Add OTAS to Dash Messaging
  • Update CAN pressure scaling (Fuel Pressure etc.)

01.01.0004

  • Add CAN Block Receive

01.01.0002

  • Increase Engine Speed validation limit.
  • Increase Inlet Manifold Pressure validation limit.
  • Add Auxiliary Output 1 Activate Race Time parameter.

01.00.0001

  • Improve integration with the Sea-Doo iBR system.
  • Add support for DSP knock control.
  • Add Fuel Closed Loop Activate group containing minimum activation conditions for closed loop operation.
  • Add Engine Load Average calculation.
  • Add Auxiliary Output N.
  • Add Auxiliary Timer.
  • Add Fuel Cylinder N Pulse Trim tables.
  • Add Ignition Cylinder N Trim Main tables.
  • Add Engine Run Time Total calculation.
  • Add Race Time calculation.
  • Add Engine Mode Switch and support Engine Mode on main engine calibration tables.
  • Add Anti Lag function.
  • Add Cruise Assist function.
  • Add No Wake Mode function.
  • Add Boost Control function.
  • Add GPS support.
  • Replace existing Launch function with launch anti-lag.
  • Rename existing Launch function to Anti Cavitation.
  • Enable basic security.

Package Structure

The items in an M1 Package are grouped by subsystems (eg Fuel, Ignition, Engine, Coolant). The top level of a subsystem contains the channels that summarise key properties and the primary calibration items. This means that an overview of a subsystem is contained in the items at the top of a tree view or with the shortest name.

The following are some of the most important package calibration items and which are fundamental to engine operation:

  • Engine Top Dead Centre for each cylinder
  • Engine Displacement: the engine capacity in litres
  • Engine Cylinders: the number of cylinders, usually a fixed value in a package
  • Engine Speed: the rotational speed of the engine, normally expressed in units of RPM
  • Engine Speed Reference Offset: the angle from the reference position to Top Dead Centre Cylinder 1
  • Engine Efficiency: the primary table used to calculate the volume of air that enters each cylinder and the following items that can be used as the table axis:
    • Inlet Manifold Pressure: the pressure in the manifold after the throttle
    • Throttle Position: a measure of the normalised throttle area derived from the Throttle Position Sensor
  • Engine Load: the mass of air that enters each cylinder which is calculated from Engine Efficiency, Engine Displacement, Engine Cylinders, Inlet Manifold Pressure and Inlet Manifold Temperature
  • Fuel Mixture Aim Main: the primary table that specifies the target Fuel Mixture Aim 
  • Fuel Volume: the volume of fuel to inject which is calculated from Engine Load, Fuel Mixture Aim, Fuel Stoichiometric Ratio and Fuel Density
  • Fuel Pressure Differential, the calculated pressure across the injector
  • Fuel Cylinder x Injector calibration. The individual injector calibrations are used to convert Fuel Volume into the injector Output Pulse Width. Each injector calibration is comprised of:
    • a Linearisation table which contains either:
      • the non-linear flow characteristic of the injector at low pulse widths, or
      • the injector dead time offset calculated from flow data
    • Reference Flow and Reference Pressure, which are used to calculate the actual Flow at Fuel Pressure Differential.
  • Coolant Temperature: used in fuel calculations to compensate for temperate effects during starting and engine warmup
  • Ignition Timing tables. Tables are provided to allow the desired timing to be calibrated against:
    • Inlet Manifold Pressure and Engine Speed
    • Throttle Position and Engine Speed
    • Engine Load and Engine Speed
  • Exhaust Lambda can be used to indicate the air / fuel ratio measured from the exhaust gas. This is available if a MoTeC LTC is fitted and is recommended for all fuel tuning.

M1 Tune Features for Online ECU Calibration

Monitored Channels

Important channels are monitored. If a Warning or Fault is detected this is reported in two ways:

  • a flashing red section of the M1 Tune status bar, and
  • a pop-up in the Windows taskbar notifications area

Active Warnings, Faults and general Information can be viewed by pressing F3 (or the Online -> Show Status... menu)

Telemetry data recording

All live telemetry data is recorded when an ECU is open and connected to M1 Tune. Telemetry Data display can be paused (Online -> Pause Telemetry Display) and then zoomed and scrolled for detailed analysis.

Engine Tuning Notes

  • The Fuel Mixture Aim Main table must be set to the desired fuel mixture. This is used in both the Fuel Volume calculations and all automatic corrections.
  • Fuel Closed Loop control can be enabled while tuning the engine and is integrated into calibration functions. If using Fuel Closed Loop during tuning it is recommended to:
    • Extend Fuel Closed Loop Control Trim Minimum and Maximum to allow control over a broader range. Recommend at least +/-30%.
    • Set Fuel Closed Loop Period to a conservative time to ensure stable control. Recommend at least 1.5s at low Exhaust Mass Flow
  • An Engine Efficiency Quick Lambda function is provided to automatically adjust the Engine Efficiency table. This function uses Exhaust Lambda Normalised for the adjustment to ensure Fuel Closed Loop control adjustments are included when adjusting the Engine Efficiency table.
Package Notes

Make: Sea-Doo

Model: RXTX RXPX

Model Year: 2010 - 2018

Target: PWC

Integration type: Vehicle Custom Plug-In ECU

Fuel: Petrol / Gasoline

Fuel Octane: 98 RON

Injectors: OEM Std.

Related Software
Versions