We use cookies on this site

< Yamaha FX SVHO 2019 (M150).June 2020

Package Yamaha FX SVHO 2019 (M150).June 2020 "Yamaha GP1800R SVHO 2021 Start File v3"

Yamaha FX SVHO 2019 (M150).June 2020
Yamaha GP1800R SVHO 2021 Start File v3
Yamaha FX SVHO 2019 (M150).June 2020
01.02.0051
6/05/2022

Make Model Model Year Target Integration Type
Yamaha GP1800R SVHO 2021 PWC Vehicle Custom Plug-In ECU



Release Notes
The Migration Notes lists the changes required, when upgrading, to maintain the same functionality from the previous version.

Current Version (01.02.0051)

  • System updated to version 1.4.0.91
  • Support for Batch Fire fuel injection added.
  • GPS via RS232 functionality added for M130 (Rev Q+) and M122 ECU's.
  • Motec GPS Module update to v1.7.21.
    • Serial Port Resource and Baud rate can be set externally.
    • Update system version to 1.4.0.0091.
    • Add support for M130 Rev Q. hardware with RS232 Rx on Udig 6 and 7.
    • Moves the serial port setup inside the GPS group.
    • Ensure a Diagnostic of Invalid Interface is reported correctly for all hardware types.
    • Allow any CAN Decode message to set the Diagnostic to OK. Allows GPS Speed message to be received by itself for example.
    • Help Updates.
  • Motec Fuel Module update to v1.18.1
    • System update to 1.4.0.91.
    • Allowance for Revolution Lock and Cylinder Lock Engine Speed Reference State in Single, Double, Triple and Quadruple Injector Fuel Volume classes. Required for Batch Fire Injection.
    Motec Input Module update to v1.10.36
    • Remove 'Diagnostic Delay' validation maximum.
    • Resource re-ordered in latchable switch class.
    Motec Comms Module updated to 1.10.3
    • System updated to v1.04.0091.
    • Serial Port class removed.
    Migration Notes;
    • Set GPS Serial Port Resource and GPS Serial Port Baud Rate if GPS Interface is RS232 Port.

01.02.0050

  • Cruise updated.
  • No Wake updated.
  • MoTeC OE Yamaha FX SVHO 2019 module updated to v 1.0.30
    • Drive Mode replaced with Drive Control Speed and Drive Control Acceleration which are written to firmware resources 10 and 11.
    • Auto Trim added and written to firmware resources 12.
    • Cruise and No Wake added to Dash CAN.
    • Dash keep alive CAN updated.
  • Driver Vehicle Speed Limit Acceleration Switch added.
  • Vehicle Speed Limit added.
  • Migration Notes;
    • Set Cruise Enable Throttle Lever Hysteresis to Cruise Throttle Lever Hysteresis from the old package.

01.02.0046

  • Race Time axis added to Fuel Mixture Aim Trim.

01.02.0045

  • Engine Start updated.

01.02.0038

  • Engine Run updated to be disabled by Engine Start Switch when Type is Push Button.

01.02.0036

  • Vehicle Tip Over updated to include a delay.

01.02.0035

  • MoTeC OE SeaDoo RXTX module updated to v 1.0.12
    • RXTX 2018 and 2019 models added.
  • Throttle Aim set to Idle while Seadoo Braking.
  • Gear Shift Mode bug fixed.
  • Vehicle Speed Limit from Seadoo Cruise added.
  • Vehicle Tip Over Warning removed.
  • Engine Start updated.
  • MoTeC OE Yamaha FX SVHO 2019 module updated to v 1.0.18
    • User Lock updated.
  • Engine Start and Run modified to suit updated Yamaha User Lock.

01.02.0029

  • Engine Start Delay added.
  • MoTeC OE Yamaha FX SVHO 2019 module updated to v 1.0.16
    • Reverse Command state changes updated.
    • User Lock updated.
  • Engine Start and Run modified to suit updated Yamaha User Lock.

01.02.0028

  • Throttle Limit added to all Warnings.

01.02.0025

  • Throttle Servo Fault Engine Speed Limit applied when Throttle Servo Bank N Diagnostic is Power Save.
  • LTC enable strategy improved to better suit marine applications.
  • Gear Source added.
  • Engine Run Time Reset Value added.
  • MoTeC OE Yamaha FX SVHO 2019 module updated to v 1.0.15
    • CAN Updates.
    • Reverse Throttle Aim updated to include Bucket Position Threshold & Hysteresis.
    • Reverse Command state changes updated.
    Migration Notes;
    • Set Yamaha Reverse Throttle Aim Bucket Position Threshold.

01.02.0018

  • Engine Oil Temperature Estimate available when sensor is not in use.
  • Engine Oil Pressure Low Switch updated.

01.02.0017

  • Fuel Tank Level Warning and Warning Light added.

01.02.0016

  • Engine Oil Pressure Low Switch Engine Speed Minimum and Hysteresis added.

01.02.0015

  • Engine Start updated.
  • Engine Stop updated.
  • Engine Oil Pressure Low Switch updated.

01.02.0010

  • MoTeC OE Yamaha FX SVHO 2019 module updated to v 1.0.5
    • CAN Updates.
  • Forward 2 removed from Gear.

01.02.0008

  • Ignition current Source always enabled
  • MoTeC OE Yamaha FX SVHO 2019 module updated to v 1.0.4
    • CAN Updates.

01.02.0007

  • MoTeC OE Yamaha FX SVHO 2019 module updated to v 1.0.3
    • CAN Updates.
    • Power Relays updated.

01.02.0006

  • Vehicle speed updated.
  • MoTeC OE Yamaha FX SVHO 2019 module updated to v 1.0.2
    • CAN Updates.

01.02.0004

  • M1 General 0x640 CAN Template reverted to version 5.
  • M1 General 0x650 CAN Template reverted to version 5.
  • M1 General 0x6A0 CAN Template reverted to version 1.
  • Engine Stop Switch bug fixed.
  • Engine Starter Motor renamed to Engine Start Motor.
  • Migration Notes;
    • Update any M1_General_0x640 CAN templates to M1_General_0x640_Version 5.
    • Update any M1_General_0x650 CAN templates to M1_General_0x650_Version 5.
    • Update any M1_General_0x6A0 CAN template to M1_General_0x6A0_Version 1.

01.02.0003

  • Coolant Pump added.
  • Engine Start updated.
  • Engine Starter Motor updated.
  • Engine Stop Switch added.
Package Notes

Make: Yamaha

Model: GP1800R

Model Year: 2021

Target: PWC

Integration type: Engine Tuning Base ECU

Engine Variant: SVHO

Fuel: Petrol / Gasoline

Fuel Octane: 98 RON

Injectors: OEM Std.

Cams: OEM Std.

Compression: 8.5:1

Cylinder head(s): OEM Std.

Exhaust manifold: OEM Std.

Inlet manifold: OEM Std.

Supercharger: OEM Std.

Waste gate: N/A.

Ignition system: OEM Std.

Coils: OEM Std.

Idle control: OEM Std. DBW

Boost control: N/A

Restrictor: N/A

Throttle: OEM Std.

CAN Nodes: Vehicle

Related Software
Versions