Package Sea-Doo RXT-X 2010 (M150).June 2020 "Sea-Doo RXP-X 2021 Rotax 1630 ACE Start File v10"

The Migration Notes lists the changes required, when upgrading, to maintain the same functionality from the previous version.

Current Version (1.02.0292)

1.02.0291

• MoTeC Input Module updated to v1.10.0081.
• Linear Ext Class updated.
• Target name changed to Offset Target.
• Scale Target added.
• Scale Q Function added.
• Scale Quantity and Display unit can be set externally.
• Offset Validation Limits removed.
• ECU Transmit Updated.
• Ignition Timing State Start Bit updated.
• Launch Engine Speed Start Bit updated.
Migration Notes
• Update M1_Watercraft_0x650 Template to v2

1.02.0290

• MoTeC OE Seadoo RXTX Module updated to v1.00.0061.
• CAN Transmit updated.

1.02.0287

• MoTeC Input Module updated to v1.10.0080.
• Linear Target name changed to Offset Target.
• Linear Scale Target added.
• Linear Scale Q function added.
• Fix Sensor Normalised Class Diagnostic, previous change prevented class from working.
• Sensor Normalised Class Diagnostic updated.
• Add Pressure Gauge Sensor classes, allows the pressure sensor type to be selected Gauge, Sealed Gauge or Absolute Types. The results of the sensors is always in Gauge, with Quantity Delta Pressure.
• Fuel Pressure Sensor class Quantity changed to Delta Pressure.
• ECU Transmit Updated.
• Added 6B0 DBC v9.
• Race Time state added to Engine Speed Limit.
• ECU Acceleration X Sensor Scale changed from constant to parameter.
• ECU Acceleration Y Sensor Scale changed from constant to parameter.
• ECU Acceleration Z Sensor Scale changed from constant to parameter.
• Race Time not resetting when launch is enabled bug fixed.
• Engine Speed Control not working when race time starts bug fixed.
• Secondary Fuel Injectors added.
Migration Notes
• Set ECU Acceleration X Sensor Scale to 8.33G.
• Set ECU Acceleration Y Sensor Scale to 8.33G.
• Set ECU Acceleration Z Sensor Scale to 8.33G.

1.02.0286

• ECU Transmit updated.
• Coolant Temperature length and offset updated.
• Coolant Pressure Start bit and length updated.
• Nitrous State Start bit updated.
• Nitrous Activate Start bit updated.
• Nitrous Switch On Start bit updated.
Migration Notes
• Updated M1_Watercraft_0x6A0 Template to v9

1.02.0275

• MoTeC OE SeaDoo RXTX Module updated to v01.00.0060.
• CAN Transmit Updated.

01.02.0269

• Exhaust Temperature Cylinder Fuel Volume Trim table added.
• Exhaust Temperature Cylinder N Fuel Volume Trim Channel added.
• Fuel Cylinder N Trim group added.
• Fuel Cylinder N Trim table renamed to Fuel Cylinder Trim Main.
• Coolant Pressure Warning Delay Enable Changed from constant to parameter.
• Engine Speed Limit Increase Rate parameter is ignored when Launch changes to disabled.
Migration Notes
• Ensure Fuel Cylinder N Trim Main table is equal to Fuel Cylinder N Trim from original package.

01.02.0266

• Fuel Pressure Control Pump Motor Volts updated so it can disable voltage correction for use with fuel pump control modules.

01.02.0265

• MoTeC Warning module reverted back to v01.04.0021.

01.02.0253

• MoTeC Fuel Module updated to v01.18.0039.
• Fuel Properties Density updated for gasoline to match calibration value of 755kg/m^3.
• Location data type can be set externally in Port Injector Class.
• MoTeC Warning Module updated to v01.04.0023.
• Minimum System updated to version 1.04.00.100.
• Mode data type change to subsystem Enable Enumeration.
• Boost Limit added to Minimum Maximum Warning with Limits class.
• MoTeC OE SeaDoo RXTX module updated to v1.00.0059.
• Firmware resource index help added.

01.02.0252

• Throttle Test Aim Minimum Validation changed to -100%.
• MoTeC Control module updated to v1.12.129.
• Throttle Test Aim Input object minimum validation set to -100% in Dual and Single Throttle Servo Class.
• Update Warning module version.
• MoTeC Warning module updated to v1.04.021.
• Mode Toggle removed from Minimum Maximum Warning and Minimum Maximum warning with Limits Classes.
• External count reset added to Minimum Maximum Warning and Minimum Maximum Warning With limits classes.
• Count Limit added which activates any of the configured warning limits while the count is above the count limit.

01.02.0248

• PWC M170 and PWC M190 configurations added. Based on PWC M130 and M150 respectively.

01.02.0247

• Jet Reverse Bucket Relay help updated.
• Jet Reverse Bucket Servo help updated.

01.02.0244

• ECU Transmit Updated.
• Fuel Tank Level 1 channel added.
• Fuel Tank Level 2 channel factor changed.
Migration Notes
• Update M1_Watercraft_0x6A0 Template to v7.

01.02.0243

• System Version update to 1.04.00.0100.
• MoTeC Fuel Module updated to 1.018.0035.
• Closed Loop Diagnostic reporting update.

01.02.0242

• ECU Transmit Updates.
• Fuel Tank 2 Level start bit overlap bug fixed.
• Gear Position start bit overlapped bug fixed.
• Gear Position Sensor Main Volt start bit updated.
• Gear Ratio start bit updated.
• Fuel Pump State start bit updated.
• Gear Shift Request Diagnostic removed from 100Hz.
• Gear Shift Request removed from 100Hz.
• Gear Shift State removed from 100Hz.
• Gear Shift Servo Diagnostics removed from 100Hz.
• Gear Shift Position Diagnostics removed from 100Hz.
• Gear Position Sensor Main Voltage removed from 100Hz.
• Gear Position removed from 100Hz.
• Gear Shift Mode removed from 100Hz.
Migration Notes
• Update M1_Watercraft_0x6A0 Template to v6.
• Update M1_Watercraft 0x640 Template to v2.

01.02.0241

• ECU Transmit Updated.
• Engine Oil Temperature signal length changed from 10 to 11 bits.
• Boost Aim signal length changed from 8 to 9 bits.
Migration Notes
• Update M1_PWC_Reduced_0x640 Template to v2.

01.02.0240.

• ECU Transmit Compile Conditions updated.

01.02.0239

• Fuel Water Content Switch help updated.

01.02.0238

• Gear Engine Speed Limit table added.
• MoTeC OE Sea Doo RXTX module updated to v1.00.0058.
• CAN Updated.
• SeaDoo Power Maximum and SeaDoo Power Minimum tables added.
• Brake State Forward Running and Brake State Braking added as criteria to Brake Lever position for setting Brake State On.

01.02.0220

• MoTeC OE Sea Doo RXTX module updated to v1.00.0036.
• 2024 RXPX model added
• CAN Updated.

01.02.0209

• Engine Start updated.

01.02.0192

• Reverted Fuel Closed Loop back to v01.02.0179.
• Reverted Knock back to v01.02.0151.
• Gear Position Sensor changed back to Normalised Tracking.

01.02.0187

• MoTeC OE Seadoo RXTX Module updated to v1.00.0029.
• CAN Transmit Updates.

01.02.0179

• Boost Aim Main Table axis changed from Throttle Position to Throttle Lever.
Migration Notes
• Confirm Boost Aim Main table values are correct for the new Throttle Lever axis.

01.02.0175

• Engine Efficiency table moved to Engine Efficiency Main.
• Jet Nozzle Pressure Sensor Validation Limits removed.
• Engine Stop Delay validation minimum allow 0ms value, which disables this delay.
• ECU Transmit Updated.
• Propeller Moving channel Added.
• ECU Transmit Reduced Mode added.
• Wastegate updated.
• Inlet Manifold Pressure State added.
Migration Notes.
• Update M1_Watercraft_6A0 Template to V5.

01.02.0162

• Fuel Water Content Switch added.

01.02.0160

• MoTeC Control Module updated to v1.12.0127.
• Boost Control with Servo Class Control Diagnostic Help updated.
• Checklists added.

01.02.0155

• Gear Position Sensor type changed from Normalised Tracking to Normalised.
• MoTeC Input Module Updated to v1.10.0071.
• Normalised Class Diagnostic updated.
• ECU Transmit Updated.
• Fuel Closed Loop Control Bank 1 Diag Channel length updated.
• Fuel Closed Loop Control Bank 2 Diag Channel start bit and length updated.
• Fuel Closed Loop State channel start bit updated.
• Fuel Cut State channel start bit updated.
• Fuel Mixture Aim Main Switch channel start bit updated.
• Fuel Mixture Aim Trim Switch channel start bit updated.
• Fuel Pressure Warning channel start bit updated.
• Fuel State channel start bit updated.
• Fuel Tank Level start bit updated.
• Fuel Water Content start bit updated.
• Fuel Temperature channel start bit updated.
• Fuel Pump State channel address changed.
• Gear Pos Sensor Main Volt channel start bit updated.
• Gear Ratio channel start bit updated.
Migration Notes.
• Confirm settings for Gear Position Sensor.
• Confirm Settings for Gear Shift Request Sensor.
• Update M1_Watercraft 6A0 Template to v4.

01.02.0151

• MoTeC Exhaust Module added
• Current Version 1.00.0012
• Exhaust Temperature Cylinder N Fuel Volume Trim added
• MoTeC Ignition Module updated to v1.11.18
• Exhaust Bank 1 Response added
• Exhaust Bank 2 Response added
• Gear Neutral Switch added
• Voltage Class added to all outputs
• Fuel Cut Estimate added
• Open Current Parameter added to all Auxiliary Outputs
• Pin Output added to all Auxiliary Outputs

01.02.0144

• Water Temperature added and added to ECU Transmit message 0x6A0
Migration Notes
• Update M1 Watercraft 0x6A0 CAN template to V3

01.02.0137

• ECU Transmit Custom CAN added
• MoTeC Comms Module updated to 1.10.25
• 800kbps baud rate added to CAN Bus class.

01.02.0131

• MoTeC Control Module Updated to 1.12.123.
• Actuator Output resource no longer required for Boost control to be active.
• Boost Control system will now operate without assigning a Boost Solenoid Normal Output Resource in Boost with Servo class.
• Neutral Gear only option added to Engine Overrun Mode.

01.02.0125

• Cruise updates.
• MoTeC OE SeaDoo RXTX module updated to v 1.0.26
• Slow Speed Enable Delay added. This overrides the hardcoded 1s delay when enabling slow Speed.
Migration Notes;
• Set Slow Speed Enable Delay to 1.0s.

01.02.0121

• MoTeC OE SeaDoo RXTX module updated to v 1.0.24
• Cruise updates.
• Slow Speed updates.

01.02.0120

• Renamed No Wake to Slow Speed with various updates to the feature.

01.02.0102

• Engine Efficiency Table load axis extended to 41 sites.
• Fuel Mixture Aim Clamp lowered to 0.3LA

01.02.0090

• Anti Lag Shutdown Exhaust Temperature refers to Exhaust Temperature Maximum.
• Engine Speed Limit Increase and Decrease Rate added. This controls the rate at which the Engine Speed Limit increases or decreases.
• Engine Overrun Vehicle Speed condition can be ignored by setting Engine Overrun Vehicle Speed Threshold to 0km/h.
• Gear axis added to Idle Ignition Timing Advance Control Proportional Gain.
• Exhaust Temperature Boost Limit table axis channel changed to Exhaust Temperature Maximum.
• Exhaust Temperature Fuel Mixture Aim table axis channel changed to Exhaust Temperature Maximum.
• Idle Throttle Pedal Blend internally clamped so that the blend point cannot exceed 100%.
• Idle State can get stuck in Test when Actuator Solenoid Resource is Not in Use bug fixed.
• Throttle Aim set to NaN from Anti Lag Throttle Aim bug fixed.
• Throttle Limit Increase and Decrease added. This controls the rate at which the Throttle Limit increases or decreases.
• System updated to version 1.4.0.97
• MoTeC Control module updated v1.12.122.
• Throttle Servo 2 (includes SENT Secure Serial Decode Type) calibration schema added to Dual Throttle Servo and Single Throttle Servo classes.
• Minimum M1 System version updated to 1.4.0.92.
• Temperature added to Boost with Servo and Boost with Dual Servo classes.
• Actuator Fault Duty Cycle & Delay added to drive the Actuator to the fully open position when Actuator Diagnostic reports a fault in the Boost with Servo and Boost with Dual Servo classes.
• Static Duty Cycle Test added to Single Throttle Servo and Dual Throttle Servo classes.
• Update Boost Control with Servo class:
• Servo Activate conditions added.
• Servo Power Save Delay added.
• Servo Actuator Test options added.
• Servo Actuator Model added.
• Servo Actuator Position Sensor Tracking with limited range support added.
• Boost Pressure axis added to Servo Actuator Control Feed Forward table.
• Servo Actuator Control Integral Negative Clamp added.
• Force close when Aim is 0% to ensure the gate is fully shut. The zero position is tracked at this time to allow for changes due to thermal expansion.
• Reset servo fault when throttle position is lifted.
• Auto zero Servo Position Sensor on ECU power up.
• Servo Temperature added.
• Servo Actuator Fault Duty Cycle & Delay added to drive the Servo Actuator to the fully open position when Servo Actuator Diagnostic reports a fault.
• MoTeC Input Module update to v1.10.58.
• Fix, a NaN value and Diagnostic of Ok could be reported at the same time on power up. Issue affected most classes.
• Add Diagnostic Delay to Voltage class.
• Remove 'Diagnostic Delay' validation maximum.
Migration Notes;
• If Boost Servo is in use;
• Set Boost Servo Default Overrun Position. Typically 0% to assist holding or building boost during overrun conditions.
• Configure Boost Servo Actuator Control Feed Forward if Boost Servo is in use. Initially this table can be setup with two axis sites (Boost Servo Actuator Aim = 0 and 100%). At Boost Servo Actuator Aim = 0% set the table value to equal Boost Servo Actuator Control Feed Forward Offset from the original package. At Boost Servo Actuator Aim = 100% set the table value to equal Boost Servo Actuator Control Feed Forward Gain + Boost Servo Actuator Control Feed Forward Offset from the original package.
• Set Boost Servo Actuator Control Integral Negative Clamp to equal Boost Servo Actuator Control Integral Minimum from the original package.
• Confirm Boost Servo Actuator Position closely follows the Boost Servo Actuator Aim when performing a step test using Boost Servo Actuator Test.

01.02.0085

• MoTeC OE SeaDoo RXTX module updated to v 1.0.20
• Alternate CAN messages added.
• Throttle Position 1-5 added.
• Brake Gear renamed to Brake State
• Brake Gear added with a firmware resource that can be used for Gear Position.

01.02.0083

• Jet Reverse Bucket Servo Function added

01.02.0079

• MoTeC OE SeaDoo RXTX module updated to v 1.0.17
• CAN OE Integration Updates for the 2021 and 2022 models.

01.02.0076

• Pressure Sensors added for, Jet Nozzle Presure, Jet Stator Pressure, Jet intake starboard and port pressure.
• Jet Reverse Bucket Function added.

01.02.0056

• Speed Only Engine Output Test added.
• MoTeC OE SeaDoo RXTX module updated to v 1.0.14
• CAN Updates.

01.02.0054

• System updated to version 1.4.0.91
• Support for Batch Fire fuel injection added.
• GPS via RS232 functionality added for M130 (Rev Q+) and M122 ECU's.
• MoTeC GPS Module update to v1.7.21.
• Serial Port Resource and Baud rate can be set externally.
• Update system version to 1.4.0.0091.
• Add support for M130 Rev Q. hardware with RS232 Rx on Udig 6 and 7.
• Moves the serial port setup inside the GPS group.
• Ensure a Diagnostic of Invalid Interface is reported correctly for all hardware types.
• Allow any CAN Decode message to set the Diagnostic to OK. Allows GPS Speed message to be received by itself for example.
• Help Updates.
• MoTeC Fuel Module update to v1.18.1
• System update to 1.4.0.91.
• Allowance for Revolution Lock and Cylinder Lock Engine Speed Reference State in Single, Double, Triple and Quadruple Injector Fuel Volume classes. Required for Batch Fire Injection.
• MoTeC Input Module update to v1.10.36.
• Remove 'Diagnostic Delay' validation maximum.
• Resource re-ordered in latchable switch class.
• MoTeC Comms Module updated to 1.10.3
• System updated to v1.04.0091.
• Serial Port class removed.
Migration Notes:
• Set GPS Serial Port Resource and GPS Serial Port Baud if GPS Interface is RS232 Port.

01.02.0050

• Cruise updated.
• No Wake updated.
• Vehicle Speed Limit added.
Migration Notes:
• Set Cruise Enable Throttle Lever Hysteresis to Cruise Throttle Lever Hysteresis from the old package.

01.02.0046

• Race Time axis added to Fuel Mixture Aim Trim.

01.02.0045

• Engine Start updated.

01.02.0042

• Driver Engine Speed Limit Switch converted to 3 position switches.
• Driver Ignition Timing Main Switch axis added to Ignition Timing Trim Main table.

01.02.0040

• Ignition Timing Trim Main added.

01.02.0039

• Driver Fuel Mixture Aim and Driver Ignition Timing Main Switches converted to 3 position switches.

01.02.0038

• Engine Run updated to be disabled by Engine Start Switch when Type is Push Button.

01.02.0036

• Vehicle Tip Over updated to include a delay.

01.02.0035

• MoTeC OE SeaDoo RXTX module updated to v 1.0.12
• RXTX 2018 and 2019 models added.
• Throttle Aim set to Idle while Seadoo Braking.
• Gear Shift Mode bug fixed.
• Vehicle Speed Limit from Seadoo Cruise added.
• Vehicle Tip Over Warning removed.
• Engine Start updated.

01.02.0029

• Engine Start Delay added.

01.02.0028

• Throttle Limit added to all Warnings.

01.02.0025

• Throttle Servo Fault Engine Speed Limit applied when Throttle Servo Bank N Diagnostic is Power Save.
• LTC enable strategy improved to better suit marine applications.
• Gear Source added.
• Engine Run Time Reset Value added.

01.02.0018

• Engine Oil Temperature Estimate available when sensor is not in use.
• Engine Oil Pressure Low Switch updated.

01.02.0017

• Fuel Tank Level Warning and Warning Light added.

01.02.0016

• Engine Oil Pressure Low Switch Engine Speed Minimum and Hysteresis added.

01.02.0015

• Engine Start updated.
• Engine Stop updated.
• Engine Oil Pressure Low Switch updated.

01.02.0010

• Forward 2 removed from Gear.

01.02.0006

• Vehicle speed updated.

01.02.0004

• M1 General 0x640 CAN Template reverted to version 5.
• M1 General 0x650 CAN Template reverted to version 5.
• M1 General 0x6A0 CAN Template reverted to version 1.
• Engine Stop Switch bug fixed.
• Engine Starter Motor renamed to Engine Start Motor.
Migration Notes:
• Update any M1_General_0x640 CAN templates to M1_General_0x640_Version 5.
• Update any M1_General_0x650 CAN templates to M1_General_0x650_Version 5.
• Update any M1_General_0x6A0 CAN template to M1_General_0x6A0_Version 1.

01.02.0003

• Coolant Pump added.
• Engine Start updated.
• Engine Starter Motor updated.
• Engine Stop Switch added.

01.02.0002

• System updated to version 1.4.0.79.
• ADR added.
• Airbox Mass Flow added.
• Airbox Temperature Sensor Resource object name changed from Airbox Temperature Sensor Voltage Resource.
• Airbox Temperature Sensor updated
• Airbox Pressure added.
• Alternative Fuel added.
• Alternator added.
• Ambient Pressure updated
• Ambient Temperature updated
• Anti Lag updated
• Anti Cavitation Mode enumeration changed. 'Disabled' value changed to 'Not in Use' to allow for hiding of unused objects.
• Anti Cavitation Throttle Limit object name changed from Anti Cavitation Throttle.
• Anti Cavitation Ignition Timing Trim object name changed from Anti Cavitation Ignition Timing Compensation.
• Auxiliary Output 1-4 Resource object name changed from Auxiliary Output 1-5 Pulse Width Modulation Resource.
• Auxiliary Output 1-4 Test added.
• Auxiliary Output 1-4 Frequency added.
• Auxiliary Output 1-4 Duty Cycle table validation limit minimum increased to -100%
• Auxiliary Output 1-4 Activate Vehicle Speed added.
• Auxiliary Output 1-4 Output object name changed from Auxiliary Output 1-5 Pulse Width Modulation.
• Auxiliary Output 1 Ignition Timing Trim object name changed from Auxiliary Output 1 Ignition Timing Compensation.
• Auxiliary Output 1 Fuel Volume Trim object name changed from Auxiliary Output 1 Fuel Volume Compensation.
• Auxiliary Output 1 Fuel Mixture Aim added. Replaces Auxiliary Output 1 Fuel Mixture Compensation
• Auxiliary Output 5 added.
• Brake State added.
• Boost updated
• Cruise object name changed from Cruise Assist.
• Cruise Mode enumeration changed. Paramaterd 'Disabled' value changed to 'Not in Use' to allow for hiding of unused objects.
• Cruise Throttle object name changed from Cruise Assist Throttle.
• Cruise Throttle Lever Hysteresis object name changed from Cruise Assist Throttle.
• Cruise enable conditions updated to include Brake State
• CAN Bus 1 object name changed from Communications CAN Bus.
• Coolant Temperature Sensor updated
• Coolant Temperature Warning updated
• Coolant Temperature Estimate added.
• Coolant Temperature Engine Speed Limit added.
• Coolant Temperature Ignition Timing Compensation table axis modified. Coolant Temperature axis sites reduced to 11. Engine Load Normalised axis added.
• Coolant Temperature Fuel Volume Compensation table axis modified. Coolant Temperature axis sites reduced to 11.
• Coolant Temperature Fuel Mixture Aim added. Replaces Coolant Temperature Fuel Mixture Compensation
• Coolant Temperature Boost Limit added. Replaces Coolant Temperature Boost Aim Compensation
• Coolant Pressure added.
• Driver Switches added.
• Driver Anti Lag Switch object name changed from Anti Lag Switch.
• Driver Cruise Set Switch object name changed from Cruise Assist Set Button.
• Driver Cruise Up Switch object name changed from Cruise Assist Up Button.
• Driver Cruise Down Switch object name changed from Cruise Assist Down Button.
• E8XX added.
• ECU CPU Usage added.
• ECU Acceleration updated
• ECU Acceleration X Sensor object name changed from ECU Acceleration X.
• ECU Acceleration Y Sensor object name changed from ECU Acceleration Y.
• ECU Acceleration Z Sensor object name changed from ECU Acceleration Z.
• ECU Battery updated
• ECU Power Relay updated
• ECU Sensor & Internal voltages updated
• ECU Receive updated
• ECU Receive object name changed from Communications Receive.
• ECU Transmit updated
• ECU TransmitlimitingVehicle CAN Bus object name changed from Communication CAN Bus.
• Engine Trip Time added.
• Engine Efficiency Boost Pressure Compensation added.
• Engine Efficiency Airbox Pressure Compensation added.
• Engine Charge Temperature added.
• Engine Charge Cooling updated
• Engine Charge Cooling Gain Primary object name changed from Engine Charge Cooling Gain.
• Engine Load Normalised added.
• Engine Speed Limit Maximum table axis modified. X axis changed to Driver engine Speed Limit Maximum Switch
• Engine Speed Limit Warning updated
• Engine Synchronisation Resource added.
• Engine Synchronisation Ignore and State added.
• Engine Run added.
• Engine Start Stop Switch object name changed from Engine Start Stop Button.
• Engine Start Stop Switch updated
• Engine Starter Motor object name changed from Starter Motor.
• Engine Starter Motor Relay Resource object name changed from Starter Motor Relay Output Resource.
• Engine Starter Motor Relay updated
• Engine Crank Idle Mass Flow added.
• Engine Crank Flooded Throttle Position added.
• Engine Crank Fuel Volume Compensation object name changed from Fuel Volume Compensation Cranking.
• Engine Post Start Idle Aim Compensation added.
• Engine Post Start Idle Mass Flow Feed Forward added.
• Engine Post Start Fuel Volume Compensation object name changed from Fuel Volume Compensation Post Start.
• Engine Oil Temperature Sensor Resource object name changed from Engine Oil Temperature Sensor Voltage Resource.
• Engine Oil Temperature Estimate added.
• Engine Oil Temperature Engine Speed Limit added.
• Engine Oil Temperature Sensor updated
• Engine Oil Temperature Warning updated
• Engine Oil Pressure Sensor updated
• Engine Oil Pressure Low Switch updated
• Engine Oil Pressure Warning updated
• Engine Oil Level added.
• Engine Temperature added.
• Engine Overrun updated
• Engine Crankcase added.
• Engine Boost Limit added.
• Engine Mode Switch removed. Replaced by Driver Fuel Mixture Aim Main Switch, Driver Ignition Timing Main Switch, Driver Engine Speed Limit Maximum Switch and Driver Throttle Lever Translation Switch.
• Exhaust Lambda Bank 1 & 2 added.
• Exhaust Lambda Warning added.
• Exhaust Lambda External removed. Use Exhaust Lambda Collector instead.
• Exhaust Lambda Collector CAN Bus added. Replaces Exhaust Lambda Collector Mode
• Exhaust Lambda Cylinder 1-3 CAN Bus added. Replaces Exhaust Lambda Cylinder 1-3 Mode
• Exhaust Pressure added.
• Exhaust Temperature Maximum added.
• Exhaust Temperature Boost Limit added. Replaces Exhaust Temperature Boost Limit Compensation
• Exhaust Temperature Fuel Mixture Aim added. Replaces Exhaust Temperature Fuel Mixture Compensation
• Exhaust Temperature Ignition Timing Compensation removed. Replaced by Engine Load Average Ignition Timing Trim.
• Exhaust Temperature Bank 1 & 2 added.
• Exhaust Temperature Collector Sensor Resource object name changed from Exhaust Temperature Collector Sensor Voltage Resource.
• Exhaust Temperature Collector Sensor updated
• Exhaust Temperature Cylinder 1-3 Sensor Resource object name changed from Exhaust Temperature Cylinder 1-3 Sensor Voltage Resource.
• Exhaust Temperature Cylinder 1-3 Sensor updated
• Exhaust Camshaft added.
• Exhaust Muffler Temperature object name changed from Muffler Temperature.
• Exhaust Muffler Temperature Sensor Resource object name changed from Muffler Temperature Sensor Voltage Resource.
• Exhaust Muffler Temperature Sensor updated
• Exhaust Muffler Temperature Warning updated
• Fuel Used Primary Correction added.
• Fuel Properties Calibration added.
• Fuel Mixture Aim Main object name changed from Fuel Mixture Aim A.
• Fuel Mixture Aim Compensation removed. No longer required.
• Fuel Mixture Aim State added.
• Fuel Volume Bank 1 & 2 added.
• Fuel Volume Transient removed. Replaced by Fuel Film.
• Fuel Mixture Aim B removed. Replaced by Fuel Mixture Aim Main and Driver fuel Mixture Aim Main Switch.
• Fuel Timing Primary object name changed from Fuel Timing.
• Fuel Timing Primary Main table axis modified. Engine Speed axis sites reduced to 11. Y axis changed to Inlet Manifold Pressure.
• Fuel Timing Primary Limit table axis modified. Engine Speed axis sites reduced to 11.
• Fuel Flow Supply & Return added.
• Fuel Film added.
• Fuel Temperature Estimate added.
• Fuel Temperature Sensor updated
• Fuel Pressure Estimate added.
• Fuel Pressure Default added.
• Fuel Pressure Control added.
• Fuel Pressure Regulator Type added. Replaces Fuel Pressure Sensor Type & Regulator Reference
• Fuel Pressure Regulator Ratio added. Replaces Fuel Pressure Sensor Type & Regulator Reference
• Fuel Pressure Sensor updated
• Fuel Pressure Warning updated
• Fuel Water Content added.
• Fuel Injector Primary updated
• Fuel Pump updated
• Fuel Pump 2 & 3 added.
• Fuel Closed Loop Mode enumeration changed. 'Disabled' value changed to 'Not in Use' to allow for hiding of unused objects.
• Fuel Closed Loop Activate Throttle Pedal added.
• Fuel Cut. added. Replaces Fuel Diagnostic
• Fuel Composition added.
• Fuel Composition Boost Limit added.
• Fuel Tank added. Replaces Fuel Level
• Fuel Cylinder 1-3 Primary Output Resource object name changed from Fuel Cylinder 1-3 Output Resource.
• Fuel Cylinder 1-3 updated
• Gear added.
• GPS updated
• Idle added. Replaces Idle Throttle
• Ignition Test added.
• Ignition Cut added.
• Ignition Coil Calibration added.
• Ignition Coil Charge object name changed from Ignition.
• Ignition Driver Firing Edge added.
• Ignition Cylinder 1-3 updated
• Ignition Cylinder 1-3 Resource object name changed from Ignition Cylinder 1-3 Output Resource.
• Ignition Output Cut Pattern added.
• Ignition Diagnostic removed. Replaced by Engine Run.
• Ignition Switch removed. replaced by Engine Run Switch.
• Ignition Timing Stop Edge removed. No longer required.
• Inlet Air Temperature object name changed from Inlet Manifold Temperature. Replaces Inlet Manifold Temperature
• Inlet Air Temperature Boost Limit added. Replace Inlet Manifold Temperature Boost Limit Compensation
• Inlet Air Temperature Fuel Mixture Aim added. Replaces Inlet Manifold Temperature Fuel Mixture Aim Compensation
• Inlet Manifold Pressure Mode added.
• Inlet Manifold Pressure Estimate added.
• Inlet Manifold Pressure Sensor updated
• Inlet Manifold Pressure Warning added.
• Inlet Manifold Pressure Correction added.
• Inlet Manifold Temperature updated
• Inlet Manifold Flap added.
• Inlet Manifold Runner added.
• Inlet Camshaft added.
• Intercooler added.
• Cruise Mode enumeration changed.
• Knock Threshold table axis modified. Engine Speed and Engine Load Normalised axes sites reduced to 11. Fuel Composition axis added
• Knock Recovery Rate table axis modified. Engine Speed axis sites reduced to 11. Engine Load Normalised axis added
• Knock Activate added.
• Knock Trim Gain table axis modified. Fuel Composition axis added.
• Knock Window DSP object name changed from Knock Window Output.
• Knock Warning updated
• Knock Cylinder 1-3 added.
• Knock Cylinder 1-3 Gain object name changed from Engine Cylinder 1-3.
• Jet Nozzle Pressure Sensor Resource object name changed from Jet Nozzle Pressure Sensor Resource.
• Jet Nozzle Pressure Sensor updated
• Jet Nozzle Angle Horizontal Sensor Resource object name changed from Jet Nozzle Angle Horizontal Sensor Resource.
• Jet Nozzle Angle Horizontal Sensor updated
• Jet Intake Pressure Sensor Resource object name changed from Jet Intake Pressure Sensor Resource.
• Jet Intake Pressure Sensor updated
• Jet Intake Temperature object name changed from Water Temperature.
• Jet Trim Sensor Resource object name changed from Jet Trim Sensor Resource.
• Jet Trim Sensor updated
• Lap added.
• Lanyard Switch updated
• Lanyard added.
• Launch Engine Speed table axis modified. Driver Launch Aim switch axis added
• Launch Fuel Volume Trim object name changed from Launch Fuel Volume Compensation.
• Launch Switch removed. Replaced by Driver Launch Switch
• Logging throttle Lever added.
• Logging Engine Speed added.
• Logging Unload added.
• LTC added.
• LTC Power Save Delay object name changed from Exhaust Lambda Power Save Delay.
• Nitrous added.
• No Wake object name changed from No Wake Mode.
• No Wake Mode added.
• No Wake Enable added.
• No Wake Throttle Aim object name changed from No Wake Mode Throttle.
• PDM added.
• Race Time Mode added.
• Race Time Mode updated
• Race Time Activate Vehicle Speed added.
• Race Time Activate Delay added.
• Race Time Reset added.
• Race Time Boost Limit added. Replaces Race Time Boost Limit Compensation
• Race Time Fuel Mixture Aim added. Replace Race Time Fuel Mixture Aim Compensation
• Race Time Ignition Timing Trim object name changed from Race Time Ignition Timing Compensation.
• Race Time Throttle Limit added. Replaces Race Time Throttle Lever Compensation
• SeaDoo CAN Bus added.
• SeaDoo Model object name changed from Communications SeaDoo Model.
• SeaDoo ADL Diagnostic object name changed from Communications ADL Diagnostic.
• SeaDoo Brake object name changed from Brake.
• SeaDoo GPS object name changed from Communications GPS.
• SLM added.
• Steering Angle added.
• Steering Force added.
• Steering Pressure added.
• Steering Lock Switch Resource object name changed from Steering Lock Switch State Resource.
• Steering Lock Switch updated
• Steering Lock Throttle Aim object name changed from Steering Throttle.
• Tachometer added.
• Throttle Area table axis modified. Throttle Servo Position axis sites increased to 41
• Throttle Lever Sensor Main Resource object name changed from Throttle Lever Sensor Main Voltage Resource.
• Throttle Lever Sensor Tracking Resource object name changed from Throttle Lever Sensor Tracking Voltage Resource.
• Throttle Lever Translation table axis modified. Engine Speed axis sites reduced to 21. Driver Throttle Lever Translation Switch axis added.
• Throttle Lever Sensor updated
• Throttle Lever Compensation removed. Replaced by Throttle Limit.
• Throttle Limit added.
• Throttle Aim Diagnostic added.
• Throttle Aim Minimum added.
• Throttle Cranking removed. Replaced by Throttle Aim Minimum and Idle control system
• Throttle Dashpot removed. Replaced by Idle control system
• Throttle Position Fuel Mixture Aim added.
• Throttle Position Estimate added.
• Throttle Position Sensor added.
• Throttle Servo updated
• Throttle Test updated
• Turbocharger added.
• VCS added.
• Vehicle Speed updated
• Vehicle Acceleration Lateral Sensor Resource object name changed from Vehicle Acceleration Lateral Sensor Voltage Resource.
• Vehicle Acceleration Lateral Sensor updated
• Vehicle Acceleration Longitudinal Sensor Resource object name changed from Vehicle Acceleration Longitudinal Sensor Voltage Resource.
• Vehicle Acceleration Longitudinal Sensor updated
• Vehicle Acceleration Vertical Sensor Resource object name changed from Vehicle Acceleration Vertical Sensor Voltage Resource.
• Vehicle Acceleration Vertical Sensor updated
• Vehicle Tip Over Switch updated
• Vehicle Tip Over Switch Resource object name changed from Vehicle Tip Over Switch State Resource.
• Vehicle Tip Over Warning updated
• Warning Source added.
• Warning Mode added.
• Wastegate added.
Migration Notes:
• Refer to migration document for this version.

Previous Version (01.01.0022)

Make:SeaDoo

Engine Variant: Rotax 1630

Year: 2021

Integration Type: Vehicle Custom Plug-In ECU

Fuel: Petrol / Gasoline

Fuel Octane: 98 RON

Injectors: OEM STD

Cams: OEM STD

Compression: OEM STD

Cylinder Head: OEM STD

Exhaust Manifold: OEM STD

Inlet Manifold: OEM STD

Turbo:N/A

Wastegate:N/A

Ignition System: OEM STD

Coils: OEM STD

Idle Control: OEM STD. DBW

Boost Contol: N/A

Throttle: OEM STD

CAN Nodes: LTC/Dash/iBR/GPS

Minimum M1 System Version	01.04.00.0100
Minimum M1 Tune Version	1.4.4.922

Version
01.02.0243
01.02.0266
01.02.0292
01.02.0296